8. Programmable Features
35
Code #49: Setting the auto disconnection
AUTO DISCONNECT
=ON [±]
To answer a call with an extension telephone in TEL/FAX
mode (page 25), activate this feature and program the
code.
1. Press {MENU}.
2. Press {#}, then {4}{9}.
3. Press {A} or {B} repeatedly to select “ON”.
4. Press {SET}.
5. Enter your code from 2 to 4 digits, using 0-9 and
{*}.
L The default code is “;0”
6. Press {SET}.
7. Press {MENU}.
Code #54: Changing the recording time for your
TAM/FAX greeting message (KX-FT988 only)
GREETING TIME
=16s [±]
“16s” (default): Maximum recording time is 16 seconds.
“60s”: Maximum recording time is 60 seconds.
See page 29 for details.
Code #58: Setting the scan contrast
SCAN CONTRAST
=NORMAL [±]
To send or copy a document with faint or dark writing, set
this feature before starting transmission or copying.
“NORMAL” (default): Used for normal writing.
“LIGHT”: Used for dark writing.
“DARKER”: Used for faint writing.
L This feature is not valid if you select “PHOTO”
resolution for sending (page 20) or copying (page 28)
a document.
Code #59: Setting the print contrast
PRINT CONTRAST
=NORMAL [±]
To adjust the darkness of received or copied documents.
“NORMAL” (default): Normal contrast.
“DARKER”: Darker contrast.
Code #67: Setting the incoming message monitor
(KX-FT988 only)
ICM MONITOR
=ON [±]
To hear an incoming message (ICM) from the speaker
when the answering device is recording the message.
“ON” (default): You can monitor the incoming message.
“OFF”: Deactivates this feature.
Code #72: Setting recall/flash time
SET FLASH TIME
=600ms [±]
The recall/flash time depends on your telephone
exchange or host PBX. You can select “900ms”,
“700ms”, “600ms” (default), “400ms”, “300ms”,
“250ms”, “200ms”, “160ms”, “110ms”, “100ms”,
“90ms” or “80ms”.
Note:
L If the unit is connected via a PBX, this setting may
need to be changed in order for PBX functions
(transferring a call, etc.) to work correctly. Consult
your PBX supplier for the correct setting.
L If you set the location setting to “CZECH” or
“SLOVAKIA” (feature #74 on page 35), the default
setting will be “100ms”.
Code #73: Changing the receiving mode in the
manual answer setting
MANUAL ANSWER
=TEL [±]
“TEL” (default): Telephone mode (page 24)
“TEL/FAX”: Telephone/Fax mode (page 25)
Code #74: Setting the location where you use this
unit
LOCATION
=EAST EUROPE [±]
This setting must match your location.
“EAST EUROPE” (default): To use in East Europe
countries.
“CZECH”: To use in Czech Republic.
“SLOVAKIA”: To use in Slovakia.
Code #76: Setting the connecting tone
CONNECTING TONE
=ON [±]
If you often have trouble when sending faxes, this feature
allows you to hear connecting tones: fax tone, ring back
tone and busy tone. You can use these tones to confirm
the status of the other party’s machine.
“ON” (default): You will hear connecting tones.
“OFF”: Deactivates this feature.
Note:
L If the ring back tone continues, the other party’s
machine may not be a fax machine or may have run
out of paper. Check with the other party.
L The connecting tone volume cannot be adjusted.
Code #77: Changing the receiving mode in the auto
answer setting (KX-FT988 only)
AUTO ANSWER
=TAM/FAX [±]
“TAM/FAX” (default): Telephone Answering
Machine/Fax mode (page 25)
To Next Page
Loading...
