Panasonic KX-HTS824 - Page 9

1.1 For Your Safety
For All Telephone Equipment
･ The
p
roduct should be ke
p
t free of dust, moisture, hi
g
h tem
p
erature
(
more than 40 °C
)
and vibration, and
should not be exposed to direct sunlight.
･ Un
p
lu
g
the
p
roduct from the wall outlet before cleanin
g
. Wi
p
e the
p
roduct with a soft cloth. Do not clean
with abrasive powders or with chemical agents such as benzine or thinner. Do not use liquid cleaners or
aerosol cleaners.
For the PBX
･ Do not install the s
y
stem in the followin
g
locations:
a. In direct sunlight and hot, cold, or humid places. (Temperature range: 0 °C to 40 °C)
b. Areas where sulphuric gases may be present, such as near thermal springs.
c. Near devices that
g
enerate hi
g
h fre
q
uencies, such as sewin
g
machines or electric welders.
d. Locations where other objects will obstruct the area around the PBX. Be especially careful to leave at
least 5 cm to the sides of the PBX for ventilation.
e. Locations where condensation can occur.
･ Do not block the o
p
enin
g
s of the PBX. Allow s
p
ace of at least 20 cm above and 10 cm at the sides of the
PBX.
･ When installin
g
or removin
g
the o
p
tional service cards, do not
p
ut
p
ressure on an
y
p
arts of the mother
board. Doing so may result in damage to the PBX.
･ Once
y
ou have started the PBX, if
y
ou un
p
lu
g
the PBX, do not initialise it a
g
ain as described in "S
y
stem
Initialisation Procedure". Otherwise,
y
our
p
ro
g
rammed data will be cleared. To restart the PBX, refer to
"6.1.4 Restartin
g
the PBX".
･ Before touchin
g
the
p
roduct
(
PBX, cards, etc.
)
, dischar
g
e static electricit
y
b
y
touchin
g
g
round or wearin
g
an earthing strap. Failure to do so may cause the PBX to malfunction due to static electricity.
･ When relocatin
g
the e
q
ui
p
ment, first disconnect the telecom connection before disconnectin
g
the
p
ower
connection. When the unit is installed in the new location, reconnect the power first, and then reconnect
the telecom connection.
･ The
p
lu
g
of
p
ower su
pp
l
y
cordset is used as the main disconnect device. Ensure that the AC outlet is
located near the equipment and is easily accessible.
･ Slots and o
p
enin
g
s in the front, back and bottom of the cabinet are
p
rovided for ventilation; to
p
rotect it
from overheating, these openings must not be blocked or covered. The openings should never be blocked
by placing the product on a bed, sofa, rug, or other similar surface while in use. The product should never
be placed near or over a radiator or other heat source. This product should not be placed in a sealed
environment unless proper ventilation is provided.
･ Make sure that the surface behind the PBX is flat and free of obstacles, so that the o
p
enin
g
s on the back
of the PBX will not be blocked.
･ When this
p
roduct is no lon
g
er in use, make sure to detach it from the rack or wall.
･ Use onl
y
the AC
p
ower cord included with the PBX. A certified
p
ower su
pp
l
y
cord has to be used with this
equipment. The relevant national installation and/or equipment regulations shall be considered. A certified
power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227
(designation H05VV-F 3G 0.75 mm2) shall be used.