Panasonic KX-NS0154 - Page 40

40
KX-NS0154
G13 PLL3_DVDD PLL3 Digital PI
G14 SPI1DI SPI2 Serial Data In I
G15 TCK JTAG Clock I
G16 TDI JTAG Data In I
G17 EXTINT15_SYNCPORT IC501 SPI handshake I
G18 RF_RADIO_EN_EXTINT9 IC503 SPI handshake O
G19 MAIN_CLK_OUT DVF-DCX(IC503) handshake for SPI I
H1 MEMXD8_LCDD12 PHY RESET O
H2 MEMDQMBLS0_LCDD17 not used O
H3 MEMCS2_EXTINT6 Timer from PHY I
H4 MEMCS3_EXTINT7 not used O
H5 VDD 1.2 V Core PI
H6 VDDIO General I/O PI
H7 GND GND Connection P
H8 GND GND Connection P
H9 GND GND Connection P
H10 GND GND Connection P
H11 GND GND Connection P
H12 GND GND Connection P
H13 PLL3_AVSS PLL3 Analog GND P
H14 ETEST EFUSE Test signal (Not used) I
H15 TMS JTAG Mode Select I
H16 TDO JTAG Data Out O
H17 RF_SDATA_IN_SD_D3 IC503 SPI handshake O
H18 RF_TR_DATA_EXTINT10 IC501 SPI handshake I
H19 RF_SLOT_CTRL_SD_DETECT IC501 SPI handshake O
J1 MEMXD9_LCDD13 not used O
J2 MEMXD7_LCDD11 Blue LED control O
J3 MEMDQMBLS1_EXTINT5 not used O
J4 MEMWR Memory Write (Not used) O
J5 VDDIO General I/O PI
J6 GND GND Connection P
J7 GND GND Connection P
J8 GND GND Connection P
J9 GND GND Connection P
J10 GND GND Connection P
J11 GND GND Connection P
J12 OSC25M_VSS Oscillator 25 MHz GND P
J13 OSC25M_VDD12 Oscillator 25 MHz 1.2 V PI
J14 IF_T_DATA GPIO (Not used) O
J15 IF_RX1 IC501 SPI handshake O
J16 RF_SEN_SD_WR_PROT IC501 SPI handshake O
J17 RF_SCLK_SD_D2 IC501 SPI handshake O
J18 RF_SDATA_OUT_SD_D1 IC501 SPI handshake O
J19 IF_EN_DA TDM-DRX for IC503 I
K1 MEMXD6_LCDD10 Red LED control O
K2 MEMXD5_LCDD7 Green LED control O
K3 MEMXD10_LCDD14 not used O
K4 MEMXD11_LCDD15 not used O
K5 VDD 1.2 V Core PI
K6 GND GND Connection P
K7 GND GND Connection P
K8 GND GND Connection P
K9 GND GND Connection P
K10 GND GND Connection P
K11 GND GND Connection P
K12 VDDIO General I/O PI
K13 VDD 1.2 V Core PI
K14 IF_INT_ANA GPIO (Not used) O
K15 IF_MLSE GPIO (Not used) O
K16 IF_NARES GPIO (Not used) O
K17 IF_DATA_DA TDM FSYNC for IC503 I
K18 AMPOUT0 Output of Out Amplifier 0 (Not used) O
K19 AMPOUT1 Output of Out Amplifier 1 (Not used) O
L1 MEMXD3_LCDD5 Not used O
L2 MEMXD13_LCDD19 not used O
L3 MEMXD14_LCDD20 not used O
Pin No. Terminal Name Contents of Control I/O setting Remark