Panasonic Omnivision PV-V4620 User Manual

Before Requesting Service
Check the following points once again if you are having trouble with your VCR.
Power Correction
No power... « Completely insert Power Plug into an AC outlet,
+ Set POWER button to on.
* Make sure power source is active.
Recording & Playback Correction
TV program cannot be recorded... Check connections between VCR, external antenna, and TV.
Check hook up selection. (P.4~5)
Make sure your antenna system (CABLE or TV) is correctly set.
(Channels (P.38])
Make sure cassette record tab is intact. (P.40)
Timer recording cannot be performed... Check clock is set to current time and date.
Make sure Cable/DSS box (if used) is left on and tuned to
channel to be recorded.
Set recording start/stop times correctly. (P.12)
Make sure POWER button is set to off. (P.12, 13)
Timer recording may not be performed or continued if a power
interruption of more than 1 minute occurs before or during, a
Timer Recording, even after power is restored,
es
There is no playback picture, or the playback Select channel 3 or 4 on TV to match VCR output channel (3 or 4)
picture is noisy or contains streaks... (P.6) or select LINE.
Set VCR/TV selector to “VCR.”
Adjust TRACKING control in either direction. (P.41)
Try Head Cleaning. (P.41)
Special effects playback, picture may contain Set TV's Vertical Hold Control to MANUAL, then adjust.
some vertical jitter when using a TV with an
Automatic Vertical Hold Control...
VCR cannot be controlled... Make sure VCR LOCK is set to off. (P.36)
Make sure remote is in proper mode. (P.20)
Make sure unit is not in a Timer Record operation.
Remote Control Correction
VCR
cannot
be
remote
controlled...
Aim
Remote
Control
directly
at
remote
sensor
on
VCR.
(P.50)
Avoid
any
object
blocking
signal path.
Check
remote
batteries.
(P.4)
Make
sure
VCR LOCK
is
set
to
off.
(P.36)
Exposing
VCR
remote
sensor
to
direct
fluorescent
or
outdoor
light
may cause
signal
interference.
ACTION and PROG/VCR+ buttons cannot be e Press VCR button for VCR mode. (P.20)
used... * Check remote Batteries. (P.4)
Miscellaneous Correction
Programs cannot be viewed on TV... * Set VCR/TV selector to “TV.” (P.9)
e Make sure proper signal source is selected.
Video cassette cannot be inserted... e Insert the cassette with window side up; record tab facing you.
e Insure no other tape is inside unit.
Video cassette cannot be removed... * Completely insert Power Plug into AC outlet
Video cassette ejects when a recording is started] +» Make sure cassette record tab is intact. (P.40)
or the power is turned off for timer recording...
In
Stop
mode,
the
motor
(CYLINDER)
continues
|
*
To
enable
Quick
play
mechanism,
the
cylinder
will
rotate
for
to
rotate...
about
5
minutes. This
reduces
response
time from
Stop
to
Play
mode
and from
Piay to
Rewind Search
mode.
The
top
of
the
playback
picture
waves
back
and
Because
VCR
playback
signal
is
not
as
stable
as
off-the-air
TV
forth excessively... signal, top of TV screen may be bent or unstable during
playback. Slowly turn TV horizontal Hold control to correct. If
your TV has no horizontal Hold control or adjusting control is
ineffective, contact your nearest TV service center.
If you cannot resolve the problem, please call the Customer Satisfaction Center for
product assistance at 201-348-9090.
To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).
44 For assistance, call 1-800-211-PANA(7262).

Panasonic Omnivision PV-V4620 Specifications

General

Brand	Panasonic
Model	Omnivision PV-V4620
Category	VCR
Language	English