Panasonic PT-AE7000U

Technical information
ENGLISH - 99
Appendix
Command Control contents Remarks
VXX
LENS MEMORY
LOAD
Loads LENS MEMORY.
LMLI0 = +00000 = LENS MEMORY 1 LMLI0 = +00001 = LENS MEMORY 2
LMLI0 = +00002 = LENS MEMORY 3 LMLI0 = +00003 = LENS MEMORY 4
LMLI0 = +00004 = LENS MEMORY 5 LMLI0 = +00005 = LENS MEMORY 6
GAMMA
ADJUSTMENT
Sets Y ADJUST. (OUTPUT)
AGOS0 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
Sets R ADJUST. (OUTPUT)
AGOS1 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
Sets G ADJUST. (OUTPUT)
AGOS2 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
Sets B ADJUST. (OUTPUT)
AGOS3 = p1p2d1d2d3d4
p1p2 = POINT (01 - 09) d1d2d3d4 = OUTPUT (0000 - 0255)
Sets GAMMA ADJUSTMENT. (INPUT)
AGIS0 = p1p2d1d2d3
p1p2 = POINT (01 - 09) d1d2d3 = INPUT (001 - 099)
TRIGGER 1
(OUTPUT)
Switches TRIGGER 1 (OUTPUT) when RS-232C COMMAND LINK is set in the TRIGGER 1
SETTING menu.
TROI0 = +00000 = LOW TROI0 = +00001 = HIGH
TRIGGER 2
(OUTPUT)
Switches TRIGGER 2 (OUTPUT) when RS-232C COMMAND LINK is set in the TRIGGER 2
SETTING menu.
TROI1 = +00000 = LOW TROI1 = +00001 = HIGH
<Inquiry commands>
Command Control contents Parameter
QPW Power status 000 = OFF 001 = ON
QIN INPUT signal status
CP1 = COMPONENT IN SVD = S-VIDEO IN
VID = VIDEO IN HD1 = HDMI 1 IN HD2 = HDMI 2 IN HD3 = HDMI 3 IN
RG1 = COMPUTER IN
QPM
PICTURE MODE
status
NOR = NORMAL DYN = DYNAMIC 709 = REC709 DCN = D-CINEMA
CN1 = CINEMA1 CN2 = CINEMA2 GM1 = GAME (

page 40)
QSH BLANK status 0 = OFF 1 = ON (

page 79)
QFZ FREEZE status 0 = OFF 1 = ON (

page 79)
QOT
OFF TIMER
status
0 = OFF 1 = 60MIN. 2 = 90MIN. 3 = 120MIN. 4 = 150MIN.
5 = 180MIN. 6 = 210MIN. 7 = 240MIN. (

page 76)
QWM
WAVEFORM
status
Parameter
0 = OFF 1 = FULL SCAN(Y) 2 = FULL SCAN(R) 3 = FULL SCAN(G)
4 = FULL SCAN(B) 5 = SINGLE LINE SCAN(Y) 6 = SINGLE LINE SCAN(R)
7 = SINGLE LINE SCAN(G) 8 = SINGLE LINE SCAN(B)