Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 147
[LIGHT RUNTIME] Displays the runtime of the light source 1 and the light source 2.
[CONTINUOUS LIGHTING
TIME]
Displays the elapsed time from when the light source is illuminated.
The elapsed time after the illumination of the light source can be conrmed when adjusting the focus.
The elapsed time is reset when the light source is temporarily turned o such as using the shutter
function.
[FIRMWARE VERSION] Displays the rmware version of the of the projector.
[INTAKE AIR TEMP.]
*1
Displays the intake air temperature status.
[EXHAUST AIR TEMP.]
*1
Displays the exhaust air temperature status.
[LIGHT1 TEMP.]
*1
Displays the status of the light source 1 temperature of the projector.
[LIGHT2 TEMP.]
*1
Displays the status of the light source 2 temperature of the projector.
[SELF TEST] Displays the self-diagnosis information.
[INPUT] Displays the input terminal currently selected.
[SIGNAL NAME] Displays the input signal name.
[MEMORY NO.] Displays the memory number of the input signal.
[BACKUP INPUT STATUS]
Displays whether switching to the backup input signal is possible or not when [BACKUP INPUT
MODE] is set to [OFF]. (x page 111)
[NUMBER OF REGISTERED
SIGNAL]
Displays the number of registered signals.
[COOLING CONDITION] Displays the set cooling conditions.
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[REMOTE1 STATUS] Displays the control status of the REMOTE1.
[AC VOLTAGE] Displays the input supply voltage.
[ON COUNT] [POWER ON TIMES] Displays the number of times the power is turned on.
[OPERATING MODE]
Displays the setting value of the [PROJECTOR SETUP] menu → [OPERATION SETTING] →
[OPERATING MODE].
[NORMAL] Displays the runtime of the light source with [OPERATING MODE] set to [NORMAL].
[QUIET] Displays the runtime of the light source with [OPERATING MODE] set to [QUIET].
[USER1] Displays the runtime of the light source with [OPERATING MODE] set to [USER1].
[USER2] Displays the runtime of the light source with [OPERATING MODE] set to [USER2].
[USER3] Displays the runtime of the light source with [OPERATING MODE] set to [USER3].
[SIGNAL INFORMATION]
[INPUT] Displays the input terminal used for the projected image.
[SIGNAL FORMAT] Displays the format of the input signal.
[SIGNAL FREQUENCY] Displays the frequency of the input signal.
[SCAN TYPE] Displays the scan type of the input signal.
[TOTAL DOTS] Displays the total dot count of the input signal.
[DISPLAY DOTS] Displays the number of input signal display dots.
[TOTAL LINES] Displays the total line count of the input signal.
[DISPLAY LINES] Displays the number of input signal display lines.
[SAMPLING]
Displays the sampling information and the color format of the input
signal.
[SIGNAL LEVEL] Displays the signal level of the input signal.
[BIT DEPTH] Displays the gradation of the input signal.
[HDCP STATUS]
Displays the HDCP status of the input signal. The content of display
is as follows.
[HDCP2.X]: When protected with HDCP 2.2 or HDCP 2.3
[HDCP1.X]: When protected with HDCP 1.X
[NONE]: When not protected with HDCP
[---]: When there is no signal
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is
green.
Note
f E-mail containing the status can be sent to the E-mail address (up to two addresses) set in “[E-mail set up] page” (x page 207) by
pressing the <ENTER> button while the [STATUS] screen is displayed.
f Some items in [SIGNAL INFORMATION] may be displayed and others not displayed, depending on the signal being input.
f If any abnormality has occurred on the projector, press the <DEFAULT> button while the [STATUS] screen is displayed to display the detail
screen of the error information.
f For details on the contents displayed in [SELF TEST], refer to “[SELF TEST] indications” (x page 247).
To Next Page
Loading...
