Panasonic PT-RZ970

Chapter 4 Settings — [PROJECTOR SETUP] menu
122 - ENGLISH
f To set the projector based on luminance
Luminance (lm)
When [CONSTANT MODE] is set to [OFF] When [CONSTANT MODE] is set to [AUTO] or [PC]
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Runtime (hour)
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Runtime (hour)
9 400 100.0 100.0 20 000 ― ― ―
9 000 100.0 96.0 21 000 100.0 96.0 ―
8 000 100.0 85.0 23 500 100.0 85.0 2 700
7 000 100.0 75.0 26 000 100.0 75.0 7 500
6 000 100.0 64.0 28 500 100.0 64.0 13 500
5 000 100.0 53.0 31 000 100.0 53.0 20 000
4 000 100.0 43.0 33 000 100.0 43.0 28 000
3 000 100.0 32.0 35 500 100.0 32.0 41 000
r PT-RX110
f To set the projector based on the duration of use
Duration of use
(hour)
When [CONSTANT MODE] is set to [OFF] When [CONSTANT MODE] is set to [AUTO] or [PC]
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Luminance (lm)
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Luminance (lm)
20 000 100.0 100.0 10 000 100.0 53.0 5 300
24 000 100.0 83.0 8 300 100.0 47.0 4 700
27 000 100.0 70.0 7 000 100.0 44.0 4 400
31 000 100.0 53.0 5 300 100.0 39.0 3 900
35 000 ― ― ― 100.0 36.0 3 600
40 000 ― ― ― 100.0 33.0 3 300
f To set the projector based on luminance
Luminance (lm)
When [CONSTANT MODE] is set to [OFF] When [CONSTANT MODE] is set to [AUTO] or [PC]
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Runtime (hour)
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Runtime (hour)
10 000 100.0 100.0 20 000 ― ― ―
9 000 100.0 90.0 22 500 ― ― ―
8 000 100.0 80.0 24 500 100.0 80.0 5 000
7 000 100.0 70.0 27 000 100.0 70.0 10 000
6 000 100.0 60.0 29 500 100.0 60.0 16 000
5 000 100.0 50.0 31 500 100.0 50.0 22 000
4 000 100.0 40.0 33 500 100.0 40.0 30 500
3 000 100.0 30.0 36 000 100.0 30.0 44 500
Note
f The runtime may be shorter than the estimation due to the inuence of characteristics of each light source, conditions of use, installation
environment, etc.
f The duration of use is referred to as the runtime when you use the projector successively. The duration of use is an estimated duration and
is not the warranty period.
f If the runtime exceeds 20 000 hours, replacement of the components inside the projector may be required. Consult your dealer for details.
Setting [BRIGHTNESS CONTROL SETUP]
Set the operation of the brightness control function.
The [BRIGHTNESS CONTROL SETUP] setting is synchronized with the [PROJECTOR SETUP] menu →
[BRIGHTNESS CONTROL] → [BRIGHTNESS CONTROL SETUP]. The most recent setting is reected in both
items.
1) Press as to select [OPERATION SETTING].
2) Press the <ENTER> button.
f The [OPERATION SETTING] screen is displayed.
3) Press as to select [CONSTANT MODE].