Panasonic PT-VX400U

-47-
Electrical Adjustments
Group/
Item
Item Name Function Initial Range Note
Group
101
Panel Service(6200)
0 R_LCCOM 0 0-255 * Common center Adjustmen
1 G_LCCOM 18 0255 * Common center Adjustmen
2 B-LCCOM 0 0-255 * Common center Adjustmen
3 R-ENBX-PW 5 0-15
4 G-ENBX-PW 5 0-15
5 B-ENBX-PW 5 0-15
6 R-DXIN 6 0-127
7 G-DXIN 6 0-127
8 B-DXIN 6 0-255
9 R-ENB11N 16 0-31
10 G-ENBX11N 16 0-31
11 B-ENBX11N 16 0-31
12
R-FPDDR1M
0 0-3
13 0 0-1
14 0 0-1
15
R-PARA1
1 0-7
16 0 0-1
17 R-PARA2 505 0-1023
18 R-PARA3 504 0-1023
19 R-FPDDR1 718 0-1023
20 R-FPDDR11 0 0-1023
21
G-FPDDR1M
0 0-3
22 0 0-1
23 0 0-1
24
G-PARA1
1 0-7
25 0 0-1
26 G-PARA2 505 0-1023
27 G-PARA3 504 0-1023
28 G-FPDDR1 718 0-1023
29 G-GPDDR11 0 0-1023
30
B-FPDDR1M
0 0-3
31 0 0-1
32 0 0-1
33
B-PARA1
1 0-7
34 0 0-1
35 B-PARA2 505 0-1023
36 B-PARA3 504 0-1023
37 B-FPDDR1 718 0-1023
38 B-FPDDR11 0 0-1023
Group
102
Auto Keystone Setup Value
0 OFFSET 0
-1056 -
1056
1 OFFSET SWITCH 0 0 - 1
2 DEBUG MODE 0 0 - 1
3 SERVICE CALIBRATION 0 0 - 10 * Keystone offset Adjustmen
4 LOCK COUNT 5 1 - 255
5 DELT VERT RESULT 64 1 - 255
6 ANGLE 1 COUNT 1 1 - 10
7 ANGLE 2 COUNT 5 1 - 10
8 BLIND SECTOR 1 160 0 - 1024
9 BLIND SECTOR 3 32 0 - 1024
10 BLIND SECTOR BIAS 61 0 - 1024
Group
105
Panel Service (8030)
0 Vsync input 0 0 - 1 0: Enable / 1:Disable
1 Timer for Recovery starting 0 0 - 1 0: Enable / 1:Disable
2 Color correction 0 0 - 1 0: Enable / 1:Disable
3 SPI receiver 0 0 - 1 0: Enable / 1:Disable
4 UART(UPUside) 0 0 - 1 0: Enable / 1:Disable
5
3Wire serial command gen-
erator
0 0 - 1 0: Enable / 1:Disable
6 Outputof 3 wire serial I/F 0 0 - 1 0: Enable / 1:Disable
7 ColorCorrectionTable_R 1878/1878 0 - 4095 AV / PC
8 ColorCorrectionTable_R 1878/1878 0 - 4095 AV / PC
9 ColorCorrectionTable_R 1878/1878 0 - 4095 AV / PC
10 ColorCorrectionTable_R 1977/1977 0 - 4095 AV / PC
11 ColorCorrectionTable_R 2044/2044 0 - 4095 AV / PC
12 ColorCorrectionTable_R 2048/2048 0 - 4095 AV / PC
13 ColorCorrectionTable_R 2048/2048 0 - 4095 AV / PC