Panasonic Pure IP-PBX KX-TDE600 User Manual (English)

Questions and Answers:

E
Erica StevensAug 25, 2025
Why doesn't the LINK indicator of the IP-EXT/IP-GW/IPCEMPR turn on for my Panasonic Pure IP KX-TDE600?
- V
  vwilsonAug 25, 2025
  If the LINK indicator on your Panasonic PBX's IP-EXT, IP-GW, or IPCEMPR isn't lit, it could be due to several reasons. One possibility is a malfunction of the IP-EXT or IP-GW card, or the IPCEMPR card, in which case replacing the corresponding card is the suggested solution. A poor connection could also be the culprit; ensure that you're using an 8-pin twisted pair cable, that none of the CAT 5 cables exceed 100 m in length, and that a straight cable is used for connecting to a switching hub. Finally, a network malfunction might be the cause, so ensure that all network devices are switched on.
D
David McintyreAug 27, 2025
What to do if Panasonic Pure IP KX-TDE600 does not operate properly?
- S
  Stephen CunninghamAug 27, 2025
  If your Panasonic PBX isn't operating correctly, try these steps: Press the Reset Button. Turn the power switch off, then back on. If that doesn't work, turn off the power switch, unplug the PBX, wait 5 minutes, plug it back in, and turn the power switch back on. Also, if the error no. 41 is displayed, replace the IPCMEC/ preinstalled memory card.
J
Joseph BrownAug 29, 2025
What does it mean if the RUN indicator of an Expansion Shelf does not turn on my Panasonic Pure IP KX-TDE600 PBX?
- A
  Ashley JonesAug 29, 2025
  If the RUN indicator on your Panasonic PBX's Expansion Shelf isn't turning on, there are several potential causes. First, the Bus Cable might not be connected properly, so ensure it is securely connected. Second, the Bus Cable itself (included with the BUS-M or BUS-ME card) could be defective and need replacement. Third, the optional service card (BUS-M, BUS-ME, or BUS-S) might be malfunctioning, requiring you to replace the corresponding shelf expansion card (be sure to turn off the PBX when replacing a BUS-M card). Finally, the Expansion Shelf itself could be defective and need replacement.
B
Bridget TorresAug 31, 2025
What to do if the LINK indicator of the BUS-M card of the Basic Shelf does not turn on Panasonic PBX?
- K
  Kyle PerezAug 31, 2025
  If the LINK indicator on the BUS-M card of the Basic Shelf isn't turning on, first ensure that the Bus Cable is properly connected. If it is, the Bus Cable itself (included with the BUS-M or BUS-ME card) might be defective and need replacing. Another possibility is a malfunction of the optional service card (BUS-M, BUS-ME, or BUS-S), in which case you should replace the corresponding shelf expansion card, remembering to turn off the PBX when replacing a BUS-M card.
J
johnsonamberSep 1, 2025
Why don't extensions connected to an Expansion Shelf send a dial tone on my Panasonic PBX?
- R
  Robert HenrySep 1, 2025
  If extensions connected to an Expansion Shelf aren't sending a dial tone on your Panasonic PBX, the issue could be due to a few reasons. First, check that the Bus Cable is properly connected. Second, the optional service card BUS-S might be malfunctioning, requiring you to replace the corresponding shelf expansion card. Finally, the Bus Cable itself (included with the BUS-M or BUS-ME card) could be defective and need replacement.
D
David MontgomerySep 3, 2025
What to do if my Panasonic PBX IP-PT cannot connect to the PBX?
- T
  tiffany06Sep 3, 2025
  If your IP-PT cannot connect to the Panasonic PBX, it may be due to several reasons. The wrong IP address, subnet mask address, PBX IP address, or default gateway address may have been entered, so check each parameter and enter the correct value. The Ethernet cable may not be connected correctly, so check the Ethernet cable connections. The DHCP server may not be active, so restart the DHCP server or disable DHCP and re-enter settings as appropriate.
C
Chris GlassSep 4, 2025
How to register the IP-PT on Panasonic PBX?
- J
  Julia BrownSep 5, 2025
  To register the IP-PT on your Panasonic PBX, ensure the necessary network parameters are set. If you're not using a DHCP server, set the IP address, subnet mask address, and enter the PBX IP address. If needed, also enter the IP address of the default gateway. If you're using a DHCP server, just enter the PBX IP address.
S
scott78Sep 6, 2025
How to eliminate noise on external paging with Panasonic Pure IP KX-TDE600 PBX?
- Z
  zhernandezSep 6, 2025
  To eliminate noise on external paging with your Panasonic PBX, use a shielded cable as the connection wire between the PBX and the amplifier. A short shielded cable is recommended.
J
Jessica FieldsSep 8, 2025
How to resolve distorted external music on Panasonic Pure IP KX-TDE600 PBX?
- J
  jcortezSep 8, 2025
  To resolve distorted external music on your Panasonic PBX, decrease the output level of the external music source by using the volume control on the music source.
L
Leah CastroSep 9, 2025
Why do I hear a busy tone when making calls using a SIP Extension on my Panasonic Pure IP KX-TDE600?
- C
  Cody WilliamsSep 9, 2025
  If you hear a busy tone when trying to make calls using a SIP Extension on your Panasonic PBX, the status of the port that the SIP Extension is connected to might be Out of Service. To fix this, change the port status from Out of Service to In Service using the Maintenance Console.

Panasonic Pure IP-PBX KX-TDE600 Specifications

General

Maximum Trunks	128
Maximum CO Lines	128
VoIP Support	Yes
Networking	Ethernet
Power Supply	AC 100-240V, 50/60Hz
VoIP Protocol	SIP, H.323
Rack Mount	Yes
Type	IP-PBX
Operating Temperature	0°C to 40°C (32°F to 104°F)