Panasonic SC-ALL7CD - Bluetooth Operations; Pairing and Connecting Devices; Bluetooth Settings and Disconnection

13
RQT0A83
Bluetooth
®
operations
You can listen to the sound from the Bluetooth
®
audio
device from this unit wirelessly.
≥ Refer to the operating instructions of the Bluetooth
®
device for details.
Preparation
≥ Turn on the Bluetooth
®
feature of the device and
place the device near this unit.
∫ Pairing with Bluetooth
®
devices
1 Press [CD/ ] repeatedly to select “BLUETOOTH”.
≥ If “Pairing” is indicated on the display, go to step 3.
2 Press [PLAY MENU] to select “Pairing” and then
press [OK].
≥ Alternatively, touch and hold [SELECTOR, s PAIRING]
on the unit.
3 Select “SC-ALL7CD” from the Bluetooth
®
device’s
Bluetooth
®
menu.
≥ The MAC address (e.g., 6C:5A:B5:B3:1D:0F) may be
displayed before “SC-ALL7CD” is displayed.
≥ The name of the connected device is indicated on the
display for a few seconds.
4 Start playback on the Bluetooth
®
device.
∫ Connecting a paired Bluetooth
®
device
1 Press [CD/ ] repeatedly to select “BLUETOOTH”.
≥ “Ready” is indicated on the display.
2 Select “SC-ALL7CD” from the Bluetooth
®
device’s
Bluetooth
®
menu.
≥ The name of the connected device is indicated on the
display for a few seconds.
3 Start playback on the Bluetooth
®
device.

≥ If prompted for the passkey, input “0000”.
≥ You can register up to 8 devices with this unit. If a 9th device
is paired, the device that has not been used the longest will
be replaced.
≥ This unit can only be connected to one device at a time.
≥ When “BLUETOOTH” is selected as the source, this unit will
automatically try and connect to the last connected
Bluetooth
®
device. (“Linking” is indicated on the display
during this process.) If the connection attempt fails, try to
establish a connection again.
You can change the transmission mode to prioritise
transmission quality or sound quality.
Preparation
≥ Press [CD/ ] repeatedly to select “BLUETOOTH”.
≥ If a Bluetooth
®
device is already connected,
disconnect it.
1 Press [PLAY MENU] repeatedly to select
“Link Mode”.
2 Press [2, 1] to select the mode and then press
[OK].
Mode 1: Emphasis on connectivity
Mode 2: Emphasis on sound quality

≥ Select “Mode 1” if the sound is interrupted.
≥ When enjoying video contents with this function, the video
and audio output may not be synchronised. In this case,
select “Mode 1”.
≥ The factory default is “Mode 2”.
If the sound input level from the Bluetooth
®
device is
too low, change the input level setting.
Preparation
≥ Connect a Bluetooth
®
device.
1 Press [PLAY MENU] repeatedly to select “Input
Level”.
2 Press [2, 1] to select the level and then press
[OK].
“Level 0” ,. “Level i1” ,. “Level i2”
^--------------------------------------------------J

≥ Select “Level 0” if the sound is distorted.
≥ The factory default is “Level 0”.
1 While a Bluetooth
®
device is connected:
Press [PLAY MENU] repeatedly to select
“Disconnect?”.
2 Press [2, 1] to select “OK? Yes” and then press
[OK].

≥ You can also disconnect the Bluetooth
®
device by touching
and holding [SELECTOR, s PAIRING] on the unit.
≥ The Bluetooth
®
device will be disconnected if a different
audio source (e.g., “CD”) is selected.
Connecting via Bluetooth
®
menu
Bluetooth
®
transmission mode
Bluetooth
®
input level
Disconnecting a Bluetooth
®
device
SC-ALL7CD_EGEBGN_RQT0A83-B.book 13 ページ ２０１６年３月１日 火曜日 午後４時１９分