27
RQT0A83
Troubleshooting
Before requesting service, make the following checks.
If you are uncertain about some of the check points, or
if the solutions indicated in the following guide does not
resolve the issue, then consult your dealer for
instructions.
For further dedicated help, support and advice about
your product please visit:
http://panasonic.jp/support/global/cs/audio/
(This site is in English only.)
Cannot turn on the unit.
≥ After connecting the AC mains lead, wait about 10 seconds before
turning on the unit.
Humming heard during playback.
≥ If an AC mains lead or fluorescent lights are near the cords, then
keep other appliances and cords away from the cables.
The unit does not work.
≥ One of the unit’s safety devices may have been activated.
1 Touch [Í/I] on the unit to switch the unit to standby.
≥ If the unit does not switch to standby, press and hold [∫] on
the unit for approximately 10 seconds. The unit is forcibly
switched to standby. Alternatively, disconnect the AC mains
lead, wait for at least 1 minute, then reconnect it.
2 Touch [Í/I] on the unit to switch it on. If the unit still cannot be
operated, consult the dealer.
Charging does not start.
≥ Select a source other than “USB”.
≥ If charging does not start during standby mode:
Turn the unit on. Check the charging has started, and then turn
the unit to standby mode. (l 6)
Noise is heard or the sound is interrupted.
≥ Make sure not to place any device which uses radio frequency
(e.g. mobile phone, etc.) on top of this unit.
The switches on the top panel of the unit do not
work.
≥ These switches are touch keys. Touch the switches with your
finger. They may not work if operated with your fingernails or
hands wearing gloves.
The remote control does not work properly.
≥ The battery is depleted or inserted incorrectly. (l 5)
Incorrect display or play does not start.
≥ Make sure that the disc is compatible with this unit. (l 26)
≥ There is moisture on the lens. Wait for about an hour and then try
again.
No response when [1/;] is pressed.
≥ Disconnect the USB device and then reconnect it. Alternatively,
turn the unit off and on again.
The USB drive or its contents cannot be read.
≥ The USB drive format or its contents is/are not compatible with the
unit (l 26).
≥ The USB host function of this product may not work with some
USB devices.
Slow operation of the USB flash drive.
≥ Large file size or high memory USB flash drive takes longer time
to read.
The elapsed time displayed is different from the
actual play time.
≥ Copy the data to another USB device or backup the data and
reformat the USB device.
DAB/DAB+ reception is poor.
≥ Keep the antenna away from computers, televisions, other cables
and cords.
≥ Use an outdoor antenna.
If noise is excessive during FM reception.
≥ Change the audio to be output as monaural.
1 Press [PLAY MENU] repeatedly to select “FM Mode”.
2 Press [2, 1] to select “Mono” and then press [OK].
The sound becomes monaural.
≥ To cancel, select “Stereo” or change the frequency.
In normal circumstances, select “Stereo”.
Static or noisy reception is heard while listening to
a radio broadcast.
≥ Confirm the antenna is properly connected. (l 5)
≥ Adjust the position of the antenna.
≥ Try to keep a certain amount of distance between the antenna and
AC mains lead.
≥ Try using an outdoor antenna if there are buildings or mountains
nearby.
≥ Turn the TV or other audio players off or separate it from this unit.
≥ Keep this unit away from mobile phones if there is interference.
Do you have the latest firmware installed?
Panasonic is constantly improving the system’s
firmware to ensure that our customers are enjoying
the latest technology. (l 23)
To return the settings to the factory defaults
Perform this procedure when the following situations
occur:
≥ You want to clear and reset the settings.
1 Turn the unit on.
2 Touch and hold [Í/I] on the unit until “Reset?”
appears on the display.
3 While still holding [Í/I], touch
[SELECTOR, s PAIRING] on the unit. Then
release both switches.
“Reset” appears on the display and all the indicators
flash. Wait for the display to show “Initializing”. After
“----------” is displayed, the unit will turn off.
≥ The settings are returned to the factory defaults. You will
need to make the settings again.
≥ To reset the network settings, perform the operation for
network reset. (l 25)
≥ The recorded contents in the internal memory are
maintained.
– You cannot restore the pre-recorded sample contents.
General
Remote control
Disc
USB
Radio
SC-ALL7CD_EGEBGN_RQT0A83-B.book 27 ページ ２０１６年３月１日 火曜日 午後４時１９分
To Next Page
Loading...
