24
RQT0A83
As a factory default, there will be a beep sound when
you touch the switch on the top panel of the unit.
To cancel this function
1 Press [SETUP] repeatedly to select “Buzzer”.
2 Press [2, 1] to select “Off” and then press [OK].
≥ To turn the function on, select “On” in step 2.
≥ The function works during muting as well.
This system can turn on automatically from standby
mode when this system is selected as the network
device’s output speakers.
As a factory default, the network standby is off before
you connect this system to the home network.
When you connect it to the home network for the first
time, this function will automatically switch to on.
You can also turn the network standby on by the
following steps:
1 Press [SETUP] repeatedly to select “Net Standby”
and then press [OK].
2 Press [2, 1] to select “On” and then press [OK].
≥ When “Net Standby” is “On”
– The network (wired LAN/Wi-Fi) will be active even
in standby mode.
– The power consumption in standby mode will
increase. To reduce the power consumption in
standby mode, turn off the network standby.
To turn off the network standby
Select “Off” in step 2.
≥ When you have turned “Net Standby” to “Off”
– The network (wired LAN/Wi-Fi) will be disabled in
standby mode if the system is switched to standby
mode at a source other than “NETWORK”.
The network (wired LAN/Wi-Fi) will be enabled
when the system is turned on.
– Network standby will be active if the system is
switched to standby mode at “NETWORK”
selector mode and this system is connected to the
network.
– To keep the network standby turned off, select a
source other than “NETWORK” before switching
the unit to standby mode.
≥ This function will return to default setting if you have
performed the operation for network reset. (l 25)
≥ When the system is turned on by this feature, the beginning
part of the music may not be played back.
≥ Depending on the app, the conditions for activating this
function may differ.
≥ The system may not turn on even when selected as the
output speakers. In that case, start playback.
The wireless LAN function can be enabled or disabled.
1 Press [RADIO, EXT-IN] repeatedly to select
“NETWORK”.
2 Press [SETUP] repeatedly to select
“Wireless LAN” and then press [OK].
3 Press [2, 1] to select “On” or “Off” and then press
[OK].
≥ The factory default is “On”.
To check the Wi-Fi signal strength where this system is
located.
Preparation
Connect this system to the wireless network. (l 7)
1 Press [RADIO, EXT-IN] repeatedly to select
“NETWORK”.
2 Press [SETUP] repeatedly to select “Signal Level”
and then press [OK].
“Level ” is indicated on the display.
(“ ” stands for a number.)
≥ Press [OK] to exit this display mode.
≥ It is recommended to have a signal strength of “3”. Change
the position or angle of your wireless router or this system if
the indication is “2” or “1” and see if the connection improves.
≥ If “Level 0” is displayed, this system cannot establish a link
with the wireless router. (l 29)
Display the name for the connected wireless network
(SSID).
1 Press [RADIO, EXT-IN] repeatedly to select
“NETWORK”.
2 Press [SETUP] repeatedly to select “Net Info” and
then press [OK].
3 Press [2, 1] repeatedly to select “SSID” and then
press [OK].
≥ Press [OK] to exit.
≥ If “No Connect” is displayed this system is not connected to a
wireless network.
≥ Characters that cannot be displayed are replaced with “£”.
Beep sound setting
Network standby
Wireless LAN setting
Wi-Fi signal strength
Wireless network name (SSID)
SC-ALL7CD_EGEBGN_RQT0A83-B.book 24 ページ ２０１６年３月１日 火曜日 午後４時１９分
To Next Page
Loading...
