25
VQT3R83
Advanced
operations
∫ Changing the dual audio
Change the dual audio from main to secondary.
1
Confirm the digital audio output setting on the
connected TV or player, etc. is set to “Bitstream”.
2 Press and hold [HDMI 1/2] for more than 2 sec.
3
While the indicator of the current setting is
flashing, press [HDMI 1/2] to change the setting.
≥ The setting works only when the dual audio is
available in the audio source.
≥
The setting is maintained until it is changed again.
≥ The same setting is used for [TV] and [HDMI 1/2]
audio sources.
∫ Remote control code
When other Panasonic devices respond to this
system’s remote control, change the remote control
code on the active subwoofer and the remote control.
Preparation
≥ Turn off all other Panasonic products.
≥ Turn on this system.
Change the remote control code to code 2:
1 Aim the remote control at this system’s remote
control sensor.
2 Press and hold [MUTE] and [HDMI 1/2] on the
remote control for more than 4 sec.
≥ All the indicators will blink for 10 sec when the
code of this system is changed.
≥
The setting is maintained until it is changed again.
≥ If this system does not operate after changing the code,
repeat steps 1 and 2.
≥ To change the remote control code to code 1, repeat the
steps above, but replace [HDMI 1/2] with [TV].
∫ To turn off the 3D surround effect and
clear-mode dialog effect
Depending on your preference, it is possible to use
only the Dolby Virtual Speaker effect by turning off
the 3D surround effect and the clear-mode dialog
effect.
1 Press and hold [TV] for more than 2 sec.
≥ The indicator for the current setting blinks for 10 sec.
2 While the indicator is blinking press [TV] to
change the setting.
≥ The setting changes each time [TV] is pressed.
≥ The setting will be reset to on when this system is turned off.
∫
To turn off VIERA Link “HDAVI Control”
When “HDAVI Control” compatible equipment does
not work well with this system, for example, it is
possible to turn off this function as follows:
≥ When VIERA Link is turned off the ARC function
is not available. Be sure to connect the optical
digital audio cable. (> 19)
1 Press and hold [MUTE] on the remote control
and [s VOL] on the active subwoofer for more
than 2 sec.
2
After the setting has changed, turn off all the
connected devices and then turn them on again.
∫ To reduce the clear-mode dialog effect
When the dialog does not sound natural while the
volume is set low, for example, it is possible to
reduce the dialog enhancing effect as follows:
Press and hold [TV] on the remote control and
[s VOL] on the active subwoofer for more than
2 sec.
∫ To turn off the volume limitation
If a state of the lowered volume disturbs you every
time this system turns on, for example, it is possible
to turn off this function as follows:
Press and hold [MUTE] on the remote control and
[VOL r] on the active subwoofer for more than
2 sec.
The settings of VIERA Link “HDAVI Control”, the clear-mode dialog
effect and the volume limitation remain intact even if you switch this
system to standby mode. To turn these 3 functions back on, this
system must be set back to the factory preset. (
>
26)
≥ All the indicators will blink once when the setting is changed.
The following settings are unnecessary under
general usage conditions of the system.
A : Main
B : Secondary
A, B : Main and secondary
Only Dolby Virtual Speaker is on.
3D surround effect and clear-mode
dialog effect are also on.
SC-HTB15EGEBGNGS_VQT3R83.book Page 25 Tuesday, June 28, 2011 2:34 PM
To Next Page
Loading...
Need help?
General
Weight and Dimensions
