56 Reference & Installation Manual
Timer, all the keypad’s LEDs will be off until either a key is pressed or an access code is entered. When the system exits
Confidential Mode, the keypads will display the system’s status. Confidential Mode is activated by enabling option [3]. Option [4]
regulates whether the keypads will be activated at the touch of a key or only when an access code is entered. Option [5]
determines the amount of time without action before the system enters Confidential Mode (5 seconds or 2 minutes).
14.8 Installer Function Keys
To access the Installer Function keys, press:
[ENTER]+[INSTALLER CODE]+[MEM] = Test Report: Send the “Test Report” report code programmed in section [875] to the
monitoring station.
[
ENTER]+[INSTALLER CODE]+[STAY] = Cancel Communication: Cancels all communication with WinLoad/BabyWare software or
with the monitoring station until the next reportable event.
[
ENTER]+[INSTALLER CODE]+[SLEEP] = Answer WinLoad/BabyWare Software: Will force the console to answer an incoming call
from the monitoring station that is using the WinLoad/BabyWare software.
[
ENTER]+[INSTALLER CODE]+[BYP] = Call WinLoad Software: Will dial the PC telephone number programmed in section [915] in
order to initiate communication with a computer using the WinLoad software.
[
ENTER]+[INSTALLER CODE]+[TBL] = Installer Test Mode: The installer test mode will allow you to perform walk tests where the
siren will squawk to indicate opened zones. Press the [
TBL] key again to exit.
14.9 Daylight Savings Time
Section [730]: General Zone Options 2
Option [1] OFF = Daylight Savings Time Disabled (default)
Option [1] ON = Daylight Savings Time Enabled
With section [730] option [1] ON, the panel adjusts the system’s clock (time) for daylight savings changes. At 2:00AM on the
second Sunday of a full weekend in March, the control panel will add one hour to the programmed time (clock). At 2:00 AM on the
first Sunday of a full weekend in November, the control panel will subtract one hour from the programmed time (clock). By default,
when section [730] is set at 18, the time is set for the US, Canada etc. For other countries see Daylight Savings Programming in
the programming guide and set the country code in section [731].
14.10 Customized Daylight Saving Programming
In addition to using the default Daylight Saving Time (DST) settings in section [731], you can also set a customized DST. Set
section [732] for the DST starting period and [733] for the DST ending period. Both sections recognize 5 different entries of 2
digits each. All entries must be assigned in this respective order:
Country Code List (Default = bold)
00 = US, Canada, Mexico, St.Johns, Bahamas, Turks and
Caicos
01 = Cuba
02 = Brazil
03 = Chile
04 = Falklands
05 = Paraguay
06 = European Union, UK, and Greenland
07 = Russia and most states of the former USSR
08 = Australia- South Australia, Victoria, Australian Capital
Territory, New South Wales
09 = Lord Howe Island- Tasmania
10 = New Zealand, Chatham
11 = Tonga
12 = Iraq and Syria
13 = Israel
14 = Lebanon, Kirgizstan
15 = Palestine
16 = Egypt
17 = Namibia
18 = USA, Canada (New Daylight Saving Time for 2007)
19 = New Zealand (New Daylight Saving Time for 2007)
Months 01 to 12 01 = January
*If the day is set at 00, the DST will automatically change on
the programmed country code listed above.
Date 01 to 31 01 = First day of the month
Day 00 to 07 00 = Default*, 01 = Sunday
Hours 00 to 23 00 = Midnight
Minutes 00 to 59 00 = 60 minutes or 1 hour
Section Data Description
[732]
__/__/__/__/__/__/__/__/__/__/ Daylight Savings Time Starting Period
[733]
__/__/__/__/__/__/__/__/__/__/ Daylight Savings Time Ending Period
To Next Page
Loading...
Need help?
General
