Pelpro PPC90 User Manual (English)

Other manuals for Pelpro PPC90

User Manual32 pages

Service Manual46 pages

Questions and Answers:

C
Cheryl LopezSep 14, 2025
What does Fuel Feed Alarm Error Number 1 mean on my Pelpro PPC90 Stove?
- Z
  zjarvisSep 15, 2025
  If your Pelpro Stove displays 'Fuel Feed Alarm Error Number 1', the hopper is likely empty, or there's an auger jam. It could also be due to no vacuum, an open hopper lid, or the exhaust probe not recognizing the hot exhaust temperature despite a visible flame. Fill the hopper, inspect the feed tube for jams, inspect the venting and firebox for obstructions and clean if necessary, inspect the exhaust blower to make sure it runs, or close the hopper lid. Inspect and clean the exhaust outlet, firebox, firepot, and behind the baffles. Inspect the exhaust probe to see if it is securely attached to the side of the exhaust outlet.
M
Mrs. Sarah YatesAug 25, 2025
What to do if my Pelpro Pellet stove will not light?
- K
  Katie PriceAug 25, 2025
  If your Pelpro Pellet stove won't light, you can try the following: * Ensure the firepot holes are clean. * Verify the igniter is getting hot (glowing orange). * Inspect the stove body. * Make sure there is fuel in the hopper and the lid is securely closed. * Check that the vacuum switch is clear and connected. * Confirm all exhaust blower connections are secure. * Ensure the feed assembly and motor are free of debris. * Confirm the exhaust path is clean.
M
Matthew ThomasAug 25, 2025
What to do if pellets remain in the hopper of my Pelpro PPC90 Stove?
- K
  Kayla WilsonAug 26, 2025
  If pellets remain in the hopper, empty any pellets and vacuum any remaining pellets or debris from the hopper.
H
Haley FreemanAug 26, 2025
What to do if there is debris in the convection blower of my Pelpro PPC90?
- E
  Ethan BrownAug 26, 2025
  If you find debris in the convection blower of your Pelpro Stove, remove the right side panel to access and remove the convection blower. Then, vacuum any debris from the fan blades and blower housing.
S
Sean SmithAug 27, 2025
What to do if my Pelpro PPC90 fire starts but goes out?
- J
  Justin VelazquezAug 27, 2025
  If your Pelpro Stove starts and then goes out, make sure the firebox is clean. Ensure the firepot holes are clear. Inspect the stove body. Confirm that the exhaust probe is connected. Inspect and clean the exhaust outlet. Also, confirm the exhaust path is clean.
M
misty48Sep 12, 2025
What to do if a component (i.e. blower) fails to start or fails to turn off in my Pelpro PPC90?
- R
  Robert AguilarSep 13, 2025
  If your Pelpro Stove component, such as a blower, fails to start or fails to turn off, begin by checking that all connections and power plugs are secure. Also, visually inspect the wires, blowers, and power cord to check for a short circuit.
A
Amanda ClarkSep 12, 2025
What does Error Number 5 mean on my Pelpro Pellet stove?
- C
  Carrie KentSep 12, 2025
  Error Number 5 on your Pelpro Pellet stove indicates that the digital display is not communicating correctly with the stove control board. Inspect the cable for breaks or cuts and check the connection between the digital control and the control board. If that doesn't work, replace the component.
Z
zrobinsonSep 12, 2025
Why is there black soot on the outside of my house from my Pelpro PPC90?
- L
  landersonSep 12, 2025
  If you're seeing black soot on the outside of your house from your Pelpro Stove, make sure the exhaust path is clean and clear. You may also need to adjust the air/fuel ratio using the trim adjustment dial. Also, ensure the termination cap has at least 18” clearance to reduce the effects of soot blow-back on your home.
B
Brian CunninghamSep 4, 2025
What does Error Number 3 mean on my Pelpro Pellet stove?
- R
  rachaelstewartSep 4, 2025
  Error Number 3 on your Pelpro Pellet stove indicates that the ambient temperature is either above or below the acceptable range, or there is an ambient probe failure. It could also mean the probe is not plugged in. To solve this, try plugging the probe into the board. If that doesn't work, you may need to replace the component.
A
Alex GonzalezSep 2, 2025
What does Error Number 4 mean on my Pelpro Pellet stove?
- B
  brownanthonySep 2, 2025
  Error Number 4 on your Pelpro Pellet stove, indicates a missed ignition. This can happen due to: * Lack of fuel (hopper empty). * A jam in the feed. * The feed not turning. * A disconnected or failed feed motor. * A dirty firepot. * Issues with the igniter (no power or failed). * Debris in the igniter chamber. To resolve this, fill the hopper, inspect and clear any jams in the feed tube, inspect the feed motor circuit, clean the firepot, check the igniter leads, and clean any debris from the igniter chamber.