Pentair Fleck7000SXT - User Manual

Questions and Answers

L
Lauren CraneAug 20, 2025
What to do if my Pentair Control Unit shows Regen Failure?
- A
  Alyssa BatesAug 20, 2025
  If your Pentair Control Unit displays a Regen Failure error, it means the system hasn't regenerated for an extended period. You can perform a manual regeneration to clear the error code. If it's a metered system, check if it's measuring flow by running water and observing the flow indicator. If no flow is measured, verify the meter cable connection and meter functionality. In Master Programming Mode, ensure the unit is configured correctly, including system capacity, day override, and meter identification. If it's a Day-of-Week system, confirm at least one day is set to ON. Adjust the settings as needed.
C
Cynthia MarshallAug 22, 2025
Why is my Pentair Control Unit using too much salt?
- S
  sweeneyjacobAug 22, 2025
  If your Pentair Control Unit is using too much salt, it might be due to an improper salt setting. Check the salt usage and the salt setting to ensure they are correctly configured. It can also be caused by excessive water in the brine tank.
T
tfisherAug 25, 2025
What to do if my Pentair Control Unit has excessive water in the brine tank?
- M
  Mr. Jesus PruittAug 25, 2025
  If there is excessive water in the brine tank of your Pentair Control Unit, the drain line flow control, injector system may be plugged. You should clean the flow control, injector and screen. Alternatively, the timer might not be cycling, in which case you should replace it. Another cause might be foreign material in the brine valve or brine line flow control, so you should replace the brine valve seat and clean the valve and brine line flow control.
S
sanchezheatherAug 26, 2025
Why is my Pentair Control Unit not drawing brine?
- M
  Mark ShahAug 27, 2025
  If your Pentair Control Unit isn't drawing brine, the drain line flow control, injector, or injector screen might be plugged; clean these components. Low line pressure (below 20 psi) could also be the cause, so increase it if necessary. Other potential causes include an internal control leak, requiring replacement of seals, spacers, and the piston assembly, or the service adapter not cycling, which requires checking the drive motor and switches.
J
John AndersonAug 28, 2025
What to do if Pentair Control Unit shows Memory Error?
- J
  Jessica DiazAug 28, 2025
  If your Pentair Control Unit displays a Memory Error, it indicates a control board memory failure. Perform a Master Reset and reconfigure the system via Master Programming Mode. After reconfiguring, manually regenerate the valve. If the error persists, unplug the unit and contact technical support.
N
Nicholas RobbinsAug 30, 2025
How to fix hard water with Pentair Control Unit?
- J
  Jamie MendozaAug 30, 2025
  If you're experiencing hard water with your Pentair Control Unit, ensure the by-pass valve is closed. Check that there is enough salt in the brine tank, maintaining the salt level above the water level. Also, inspect the injector screen for any blockages and clean it if necessary. Insufficient water flowing into the brine tank can also cause hard water, so check the brine tank fill time and clean the brine line flow control if it's plugged. Other potential causes include hot water tank hardness (requiring repeated flushing), leaks at the distributor tube (check for cracks, O-ring, and tube pilot), or an internal valve leak (replace seals, spacers, and/or piston).
T
Travis StricklandSep 1, 2025
Why Pentair Control Unit water conditioner fails to regenerate?
- A
  Amber MendezSep 1, 2025
  If your Pentair water conditioner fails to regenerate, it could be due to an interruption in electrical service. Ensure permanent electrical service by checking the fuse, plug, pull chain, or switch. Another reason might be a defective timer, which would need replacement. Also, check for a power failure and reset the time of day if needed.
C
Cathy WatsonSep 2, 2025
What to do if my Pentair Control Unit has no display?
- E
  Erin HoodSep 3, 2025
  If your Pentair Control Unit has no display or only the backlight is on, the cause might be a power failure. Check that the transformer is outputting 24 volts AC. If the transformer is working, drain the super capacitor on the circuit board. Then, unplug the unit, press the reset button on the circuit board, and plug the unit back in to restore the display.
S
sarah22Sep 4, 2025
What to do if Pentair Control Unit shows Cycle Step Error?
- M
  michelebondSep 4, 2025
  If your Pentair Control Unit displays a Cycle Step Error, it indicates an unexpected cycle input. Unplug the unit and examine the powerhead, ensuring all cam switches are connected to the circuit board and functioning. Enter Master Programming mode to verify the valve type and system type are correctly set. Manually step the unit through regeneration to check its function. If the error persists, unplug the unit and contact technical support.
P
Paul RamirezSep 6, 2025
What causes loss of water pressure in Pentair Control Unit?
- P
  Peter WeberSep 6, 2025
  A loss of water pressure in your Pentair Control Unit can be caused by iron buildup in the line to the water conditioner, so clean the line. It may also be due to iron buildup in the water conditioner itself; clean the control, add mineral cleaner to the mineral bed, and increase the frequency of regeneration. Another cause could be the inlet of the control being plugged by foreign material dislodged from pipes during plumbing work; remove the piston and clean the control.

Summary

IMPORTANT PLEASE READ

General Safety and Installation Guidelines

Covers pressure, temperature limits, compliance, and professional installation requirements.

INSTALLATION

Water Pressure and Electrical Requirements

Specifies minimum water pressure and requires uninterrupted AC supply for effective operation.

Plumbing and Location Considerations

Installation Steps and Precautions

Provides step-by-step instructions for tank placement, plumbing, and initial water connection.

START-UP INSTRUCTIONS

Initial Valve Operation and Water Flow Checks

TIMER OPERATION

Metered and Time Clock Control Modes

Regeneration and Power Failure Handling

MASTER PROGRAMMING MODE CHART

MASTER PROGRAMMING MODE

Entering, Exiting, and Resetting Master Programming

Instructions on accessing, navigating, and exiting the master programming mode, including reset options.

Display Format and Valve Type Configuration

Specifies how to set display format (GAL/Ltr) and valve type (downflow, filter, etc.).

Control Type and Tank Number Setup

Guides setting the control type (metered, time clock) and the number of tanks in the system.

MASTER PROGRAMMING MODE CONTINUED

Unit Capacity, Feedwater Hardness, and Reserve Settings

Details settings for media capacity, feedwater hardness, and reserve volume selection.

Regeneration Time and Cycle Step Configuration

Covers setting the regeneration time of day and individual regeneration cycle step durations.

Day Override and Regeneration Time Configuration

Day of Week and Flow Meter Settings

USER PROGRAMMING MODE

DIAGNOSTIC PROGRAMMING MODE

Diagnostic Mode: Flow Rate and Peak Flow

Diagnostic Mode: Service Hours and Volume Used

TROUBLESHOOTING

TROUBLESHOOTING CONTINUED

Error Code Interpretation and Recovery

Lists and explains various error codes and their corresponding recovery procedures.

Service and Assembly Procedures

Pentair Fleck7000SXT Specifications

General

Model	Fleck 7000SXT
Type	Water Softener
Display	LCD
Backup Battery	Yes
Regeneration	Demand Regeneration
Resin Tank Size	10x54 inches
Warranty	5 years on valve, 10 years on tanks
Control Valve	Fleck 7000SXT Digital Control Valve