MAGICSTREAM
®
Laminar Installation and User’s Guide MAGICSTREAM
®
Laminar Installation and User’s Guide
20
To setup an AUX circuit to control the MagicStream laminar, assign the circuit light function
an auxiliary relay circuit (AUX 1), then assign the circuit name for that light circuit. The
light circuit name will appear on the main screen. Each MagicStream laminar must also be
assigned a circuit function. To assign a Circuit Name for the MagicStream laminar, go
to: MENU > SETUP > ADVANCED > CIRCUIT FUNCTIONS
Setup a MagicStream light function circuit: Assign each light auxiliary relay circuit
a circuit name, then assign that light relay circuit in the “CIRCUIT FUNCTIONS”
section, as “INTELLIBRITE.” To setup the MagicStream light circuit function (use the
“IntelliBrite” circuit name):
1. Press the button next to the AUX button (the relay auxiliary circuit
connected to the MagicStream
laminar (IntelliBrite) light).
2. Press the right or left side (PREV/NEXT) button next to “INTELLIBRITE.” Scroll
through the circuit functions until “INTELLIBRITE” is displayed.
3. Press the SAVE button on the bottom of the screen. Press the EXIT button to
return to the main screen.
4. Press the Lights button on the bottom of the screen.
5. Press the right side button next to “CONFIGURE.”
6. Press the button next to “NONE” to assign an IntelliBrite light circuit to the select-
ed button. Light names can be setup to display on the left side for “Spa” features
and on the right side for the “Pool” features.
7. Press the top left or right side button to scroll through the available light circuits
which can be used for the MagicStream laminar (IntelliBrite) lighting features.
Select at the circuit name you wish to use. The displayed circuit names are circuit
names that were previously assigned when assigning a circuit
function.
From the “Modes” screen you can select various preset show color lighting effects,
such as “American mode” and “Sunset mode,” and SAm Style (an emulation of the
SAm color scheme). Using the “Hold” and “Recall” feature you can also capture and
save a unique color effect to recall at a later time.
Modes screen: To access the IntelliBrite color show “Modes” features from the Lights
screen, press the Lights button on the bottom of the screen, then press the left side
button next to “MODES.”
Special Light Features: Up to twelve (12) IntelliBrite light circuits can be displayed
on the main Lights screen (special light features). From the Lights screen you can
activate the IntelliBrite lighting features (i.e., color swim, color set). Assuming each
MagicStream laminar (IntelliBrite) light has its own relay and separate circuit.
Activating IntelliBrite Random Mode: To toggle IntelliBrite Random Mode On or
Off you need to enter Party Mode(Off-On-Off-On), wait until the lights come on and
then enter Party Mode a second time (Off-On-Off-On) with less than 30 seconds
between them. Activating Solenoid Thumper: The solenoid thumper feature creates
a “wrinkle” in the laminar stream creating a brilliant spot of light in the laminar arc.
To g g l e t h e T hu m pe r On or Of f by en te r in g Par ty Mo d e 3 t i m es i n l e s s th a n 3 0 s e co n ds.
(Off-On-Off-On) (Wait for light to come on) (Off-On-Off-On) (Wait for light to come on)
(Off-On-Off-On) (Wait for light to come on).
Operating and Selecting MagicStream laminar (IntelliBrite) Color
Resetting All Lights: To Reset all the lights you need to enter Party Mode four (4) times
with less than 30 seconds between them. This will turn IntelliBrite Random Mode OFF.
This is needed because should two lights ever get into different states, toggling their
states will never fix the problem.
Set up a MagicStream
®
Laminar Circuit Function
Assign the MagicStream laminar circuit to the Lights screen:
To Next Page
Loading...
