Pentax EPK-i - Service Manual

Other manuals for Pentax EPK-i

Owner's Manual56 pages

Questions and Answers

H
Heather MedinaSep 8, 2025
What does 'No VCU Connection' mean on Pentax EPK-i?
- M
  Michael OrozcoSep 9, 2025
  If your Pentax Media Converter shows 'No VCU Connection', it indicates that no Endonet is connected. Ensure Endonet is properly connected.
R
Ronald BurkeAug 23, 2025
How to turn on the lamp on Pentax EPK-i?
- C
  christophergriffithAug 23, 2025
  If the lamp is not lit on your Pentax Media Converter, press J on the operation panel to turn on the lamp.
M
Michelle LewisAug 25, 2025
What to do if Pentax EPK-i says 'Please replace the lamp'?
- C
  Chad VegaAug 25, 2025
  If the message 'Please replace the lamp' appears on the monitor of your Pentax Media Converter, press J on the operation panel to turn on the lamp.
J
Jeremy JonesAug 26, 2025
What to do if no image appears on the monitor with Pentax EPK-i?
- P
  Patricia WilliamsAug 27, 2025
  If no image appears on the monitor when using your Pentax Media Converter, first, ensure the monitor is turned on and configured to the proper video input signal. Try resetting the monitor's adjustment values. Check that all cables are properly connected and the scope locking lever is in the LOCK position. Also, verify that the lamp is lit by pressing J on the operation panel.
E
Elizabeth JamesAug 27, 2025
Why does my Pentax EPK-i say 'Check USB Memory'?
- C
  Charles RodriguezAug 27, 2025
  If you see the message 'Check USB Memory' on your Pentax Media Converter, it means either no USB memory is connected or the connected USB memory doesn't have enough free space. To resolve this, connect a USB memory device that has sufficient available space to the processor.
A
Alexis CantrellSep 22, 2025
What to do if the Pentax EPK-i Media Converter shows 'Capture Failed'?
- A
  Amy NguyenSep 22, 2025
  To address the 'Capture Failed' error on your Pentax Media Converter, try capturing the scope image again.
G
Gregory JonesSep 16, 2025
What does 'Check SCOPE Connection' mean on Pentax EPK-i Media Converter?
- P
  pattersontrevorSep 16, 2025
  If your Pentax Media Converter displays 'Check SCOPE Connection', it indicates that communication with the scope has failed. Ensure that the scope is properly connected.
A
Allison McfarlandSep 18, 2025
Why do COPY and VTR functions not work on Pentax EPK-i Media Converter?
- N
  Nancy HaysSep 18, 2025
  If a long beep tone sounds and the COPY and VTR functions do not work on your Pentax Media Converter, follow these steps: 1. Change the settings for the COPY and VTR functions in the Assign scope buttons screen of [Assign scope buttons]. Remove the selection for any unused or turned off peripheral device. 2. Connect the PC and peripheral devices properly and turn them on. 3. If the capture function is selected and enabled, make sure Endoimage (OS-I1) is working properly.
P
Peter ZimmermanSep 7, 2025
What does 'PUSH LAMP SWITCH! AUX LAMP is ON' mean on Pentax EPK-i?
- P
  paulbenderSep 7, 2025
  If your Pentax Media Converter displays 'PUSH LAMP SWITCH! AUX LAMP is ON', press J on the operation panel to turn on the lamp.
D
Dan BradleySep 4, 2025
What does 'W/B Failed! Please Retry' mean on Pentax EPK-i Media Converter?
- A
  amy28Sep 4, 2025
  If you see 'W/B Failed! Please Retry.' on your Pentax Media Converter, it means the white balance is incorrect. You should set the white balance again.