Philips 10BDL3051T User Manual

IMPORTANT:
Always activate a moving screen saver program when you leave your monitor unattended.
Always activate a periodic screen refresh application if your monitor will monitor unchanging static content.
Uninterrupted monitor of still or static images over an extended period may cause “burn in”, also known
as“after-imaging” or “ghost imaging”, on your screen. “Burn-in”, “after-imaging”, or “ghost imaging” is a
well-known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or “ghost
imaging” will disappear gradually over a period of time after the power has been switched off.
Warning
Severe” burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired. The
damage mentioned above is not covered under your warranty.
Service
* The casing cover should be opened only by qualified service personnel.
* If there is any need for any document for repair or integration, please contact with your local service center.
(Please refer to the chapter of “Consumer Information Center”)
* For transportation information, please refer to “Technical Specifications”.
* Do not leave your monitor in a car/trunk under direct sun light.
Note
Consult a service technician if the monitor does not operate normally, or you are not sure what procedure to
take when the operating instructions given in this manual have been followed.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the Radio Equipment Directive (2014/53/EU). The
following test methods have been applied in order to prove presumption of conformity with the essential
requirements of the Radio Equipment Directive(2014/53/EU):
- EN60950-1
Safety of information Technology Equipment
- EN62311
Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic
fields(0HZ-300GHz)
-EN 300328(For 802.11b/g/n)
Electromagnetic compatibility and Radio spectrum Matters(ERM); Wideband Transmission systems; Data
transmission equipment operating in the 2.4GHz ISM band and using spread spectrum modulation techniques;
Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive.
-EN301489-17
Electromagnetic compatibility and Radio spectrum Matters(ERM); Electromagnetic Compatibility(EMC)
standard for radio equipment and services; Part 17:Specfic conditions for 2.4GHz wideband transmission
systems and 5GHz high performance RLAN equipment
-EN301489-1
Electromagnetic compatibility and Radio spectrum Matters(ERM); Electromagnetic Compatibility(EMC)

Philips 10BDL3051T Specifications

General

Multi-touch	Yes
Aspect ratio	16:10
Response time	30 ms
Display diagonal	10.1 \
Display brightness	300 cd/m²
Display resolution	1280 x 800 pixels
Display technology	LED
Contrast ratio (typical)	800:1
Display number of colors	262144 colors
Display diagonal (metric)	25.6 cm
Number of simultaneous touchpoints	5
Built-in camera	No
Power supply type	DC
Placement supported	Horizontal/Vertical
USB 2.0 ports quantity	1
Mean time between failures (MTBF)	50000 h
Certification	CB, CE, FCC A, UL
Product color	Black
Glass thickness	0.7 mm
Panel mounting interface	75 x 75 mm
Number of OSD languages	18
On Screen Display (OSD) languages	ARA, CHI (SIMPL), CHI (TR), DAN, DEU, DUT, ENG, ESP, FIN, FRE, ITA, JPN, NOR, POL, POR, RUS, SWE, TUR
RMS rated power	4 W
Number of built-in speakers	2
Cables included	DC, HDMI, USB
Sustainability certificates	RoHS
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	5 - 40 °C
Operating relative humidity (H-H)	20 - 80 %
Power consumption (standby)	0.5 W
Power consumption (typical)	6 W
Compatible memory cards	MicroSD (TransFlash)

Weight and Dimensions

Depth	29 mm
Width	261 mm
Height	167.2 mm
Weight	710 g