Philips C Series - Page 45

55BDL6051C 65BDL6051C
33
2. After showing Logo
3. Power state is not Power O
The options are:
{O}, {All}, {Failover}
{O}: Disable Auto signal detection
{All}: OPS -> HDMI1 -> HDMI2 -> HDMI3 -> HDMI4 ->
DisplayPort -> DVI-D ->USB-TypeC -> VGA -> Media Player
-> SmartCMS -> Home
{Failover}:
- Failover 1: OPS(default)
- Failover 2: OPS(default)
- Faliover 3: OPS(default)
- Failover 4: OPS(default)
- Failover 5: OPS(default)
- Failover 6: OPS(default)
- Failover 7: OPS(default)
- Failover 8: OPS(default)
- Failover 9: OPS(default)
- Failover 10: OPS(default)
- Failover 11: OPS(default)
- Failover 12: OPS(default)
The Failover behavior is when signal is lost, the display will
go to the next available source which is defined in priority
list in order.
Please note, the followings will suspend failover, and the
failover will resume when signal is lost again.
- Boot On Source : When the display powers on, it will go
to the source defined in this OSD option.
- Scheduler: When the display powers on by scheduler,
it will go to the corresponding source according to the
current time.
- User operation: No matter what current source it is,
when user manually changes source, the failover will
suspend.
To make sure failover starts from the 1
st
priority source after
powering on, please set the 1
st
priority source as boot on
source too.
Language
Select the language used in the OSD menu.
The options are: English/Deutsch/
简体中文
/Français/
Italiano/Español/
Pyccкий
/Polski/Türkçe/
繁體中文
/
日本語
/Português/
/Danish/Swedish/Finnish/Norwegian/
Dutch.
Power Save
Mode 1 [TCP o, WOL on, auto o]
Mode 2 [TCP o, WOL on, auto on/o]
Mode 3 [TCP on, WOL o, auto on/o]
Mode 4 [TCP on, WOL o, no auto on/o]
Power save modes
Mode 1: DC o -> Power o. LED: Red.
Power Save -> Power o, LED: Red
Mode 2: DC o -> Power o, LED: Red.
Power Save -> Power Saving. LED: Orange. Can be woken
up.
Mode 3: DC o -> Back light o, LED: Red
Power Save -> Back light o, LED: Orange. Can be woken
up.
Mode 4: DC o -> Back light o, LED: Red
Power Save -> Will not enter power save mode. show “no
signal” only.
RCU Power
Button O
No Signal Android
Mode 1 DC OFF DC OFF board power
o
Mode
2
DC OFF when signal is back,
system wake up
board power
o
Mode
3
Backlight
OFF
Backlight OFF keep power
on
Mode
4
Backlight
OFF
Backlight ON, show no
signal
keep power
on
Following table is the action for Android board with
dierent power mode.
DC o/on: press power button by RC
Power mode in
OSD
Mode 1/2 Mode 3/4
DC o shutdown 1. The current source APK(such
as MediaPlayer, Broswer or
SmartCMS) will be closed.
2. Android system will go to
the default black launcher.
DC on Boot up 1. Android system reboots
OPS settings
Set the OPS conguration under each power condition.
• {Auto} - After selecting {Card OPS} for video source
input, the OPS will be set to o when the display power
is set to o, or vice versa. If you set to other video source
inputs, the OPS will always be set to on.
• {Always o} - The OPS will always be set to o.
• {Always on} - The OPS will always be set to on.
Advanced option reset
Reset all settings in the Advanced option menu to factory
preset values.
1. Press [SET] or [
] button to enter the submenu.
2. Press [
] or [ ] button to select {Reset} and press the
[SET] button to restore settings to factory preset values.