Philips DSC 950 - Scan;-Preset)

—
a=
G3 Ry
wo
=a = =o
sak
RO
shennan eM CREE DEE RCO ERITH I ME
POWER
STANDBY/OFF
—
for
switching
on
in
stand
by
mode
OURCE
SELECT
—
for
selecting
the
desired
listening
source
S
Display — Showing:
the selected Source: LL, TUDE, GRRE, UCU PPL
the
white
source
indicators
in
the
upper
part
of
the
display
indicate
the
source
that
you
can
make
a
recording
from.
the
balance
is
indicated
under
the
white
source
indicators
with
the
Land
R
indication
(when
the
BALANCE
is
adjusted)
the
signal
strength
is
indicated
under
the
white
source
indicators
(when
the
LEVEL
ADJUST
mode
Is
entered).
the
red
RECORD
indication
lights
up
when
a
recording
source
has
been
fixed
with
the
REC.
OUT
key.
the
DIGITAL
indicator
lights
up
when
a
source
is
selected
(connected
via
a
digital
or
optical
socket
to
the
DSC950)
which
sends
a
digital
signal
to
the
DSC.
SPEAKERS
A.B.
C,
OFF
indicates
the
selected
speaker
systems.
MUTE
lights
up
when
the
volume
is
decreased
by
24
dB
LEVEL
ADJUST
lights
up
when
the
sensitivity
of
an
input
is
being
adjusted.
VOLUME indicates the volume level.
BASS,
TREBLE
indicate
the
adjustments
of
the
high
and
bass
tones
when
compensation
is
switched
off.
VVhen
compen-
sation
is
switched
on,
the
bass
and
treble
display
cisappears.
BASS — for adjusting the bass tones
TREBLE
—
for
adjusting
the
high
tones
VOLUME
—
for
adjusting
the
volume
-EVEL
—
for
adjusting
the
volume
for
the
stereo
headphones
HONES
—
socket
for
stereo
headphones
You
may
connect
a
pair
of
stereo
headphones
with
6.3
mm
plug to this socket.
Inserting
the
plug
will
net
disconnect
the
speakers.
COMPENSATION
—
for
switching
compensation
on
and
off.
Further
information
can
be
found
in
the
instructions
for
use
of
the
DSS
930
Digital
Speaker
System.
MUTE
—
for
decreasing
the
volume
by
24
dB
LEVEL
ADJUST
—
for
adjusting
the
sensitivity
of
an
Input
SOUTCe
SPEAKERS
A,B,C
—
for
switching
on
and
off
the
speaker
systems A, B and C.
DISPLAY
A/B/C/OFF
—
for
selecting
the
settings
of
a
speaker
system
to
be
shown
on
the
display
REC.
OUT
—
for
selecting
the
recording
source
AUTO
SELECT
—
for
switching
on
and
off
the
Enhanced
System Intelligence (ESI) system.
IR
SENSOR
—
infrared
remote
control
eye
a oe Ria
| 1 : 10 : G
POWER STANDBY/OFF
e Press the POWER STANDBY/OFF key 1 to switch on the
power. The Digital System Controller will enter the standby
mode and the LED above this key lights up red.
When the DSC is switched to active mode (as described
below in the chapters ‘Wake-up from standby’ and ‘SOURCE
SELECTION’), the respective indicators light up and the
standby indicator lights up green. When a remote control
command is received, this standby indicator flashes.
e To switch off the Digital System Controller press the
POWER STANDBY/OFF key again.
STANDBY
e Switching a set or your whole system to standby can only be
done
via
the
remote
control.
|
@ To switch a single source (e.g. TUNER) to standby:
Select the source using the source keys on the remote control.
— The selected source will be switched to standby if the
standby key is pressed briefly. |
If the STANDBY key is kept pressed for more than approx. 1
second the whole system will be switched to stand-by.
All light indicators will be switched off with the exception of
the standby indicator (red) on the DSC. |
When AUTO SELECT is activated the indicator of this key
also lights up during standby.
NOTE: \f the whole system is switched to standby when a
recording is active, the recording (or CD-dubbing) will be
cancelled.
8
2
Wake-up from standby
There are several options to switch your system from standby
back to operating mode:
@ Touching or turning the rotary SOURCE SELECT knob 2:
— The DSC will directly be switched to operating mode as
soan'as the SOURCE SELECT: knob:is: touched.
— When this knob is released (and not turned) all other sets in
the system (connected via the ESI sockets) become active
and all speakers in speaker system A will be activated.
= When the SOURCE SELECT knob:is touched and turned,
only the DSC, the selected source and speaker system A
will become active.
e Selecting a source with your remote control. The speakers In
the room where the remote control is used will also become
active.
e \When AUTO SELECT is activated several keys on equipment
connected via the ESI BUS sockets that activate a play
function may also be used as wake-up keys (e.g. PLAY,
SCAN;-PRESET)-
@ Pressing the DISPLAY A/B/C/OFF key 13 on your DSC.
e Pressing the SPEAKERS A, B or C key on your DSC or on
the remote control.