Philips T Line 65BDL3652T User Manual

65BDL3652T/75BDL3652T/86BDL3652T
59
• {Primary} - Designate this display as the primary display
for remote control operation. Only this display can be
operated by the remote control. (In primary mode, IR key
will always be processed regardless of the monitor ID/
group settings.)
• {Secondary} - Designate this display as the secondary
display. This display can not be operated by the remote
control, and will only receive the control signal from the
primary display via RS232C connection.
• {Lock All} / {Lock all but Volume} / {Lock all but Power}/
{Lock all except PWR & VOL} - Lock the remote control
function of this display. To unlock, press and hold the
[Info] button on the remote control for more than 6
seconds. It will exit from OSD menu automatically after
locking IR.
No warning message will be shown when IR control is locked.
Keyboard control
Choose to enable or disable the display keyboard (control
buttons) function.
• {Unlock} - Enable the keyboard function.
• {Lock All} / {Lock all but Volume} / {Lock all but Power}/
{Lock all except PWR & VOL} - Disable the keyboard
function depending on the option you selected.
NOTE: “Keyboard Control Lock Mode” This function
completely disables the access to all Keyboard
Control functions. To enable or disable the keyboard
control lock, press both [VOL+] and [UP] buttons
and hold down continuously for more than 3 (three)
seconds.
O Timer
Set automatic power o time (in hours).
Schedule
1. Default start time and end time are 00:00.
2. Start time and End time must be from the same date of
the schedule.
Schedule
1
Back Save
Enable
Start time
End time
Input
Playlist
Days of the week
Every week
Schedule list
■
Set lifecycle.
- Back:
■
Exit without saving changes.
- Save:
■
Save schedule data.
HDMI with One Wire
CEC control.
• {O} - Disable CEC.(Default)
• {On} - Enable CEC.
The following features are supported:
• One Touch Play allows devices to switch the display to use
it as the active source when playback starts.
• System Standby enables users to switch multiple devices
to standby mode with the press of one button (HDMI
with One Wire Power o is On).
Auto signal detection
This function allows the system to detect and display the
available signal sources automatically.
Conditions for Auto Signal Detection:
1. Sub mode is “O”
2. After showing Logo
3. Power state is not Power O
The options are:
{O}, {All}, {Failover}
{O}: Disable Auto signal detection
{All}: OPS -> HDMI1 -> HDMI2 -> HDMI3 -> HDMI4 ->
DisplayPort -> DVI-D ->USB-TypeC -> VGA -> Media Player ->
SmartCMS -> Home
{Failover}:
- Failover 1: OPS(default)
- Failover 2: OPS(default)
- Faliover 3: OPS(default)
- Failover 4: OPS(default)
- Failover 5: OPS(default)
- Failover 6: OPS(default)
- Failover 7: OPS(default)
- Failover 8: OPS(default)
- Failover 9: OPS(default)
- Failover 10: OPS(default)
- Failover 11: OPS(default)
- Failover 12: OPS(default)
The Failover behavior is when signal is lost, the display will
go to the next available source which is dened in priority
list in order.
Please note, the followings will suspend failover, and the
failover will resume when signal is lost again.
- Boot On Source : When the display powers on, it will go
to the source dened in this OSD option.
- Scheduler: When the display powers on by scheduler,
it will go to the corresponding source according to the
current time.
- User operation: No matter what current source it is,
when user manually changes source, the failover will
suspend.
To make sure failover starts from the 1
st
priority source after
powering on, please set the 1
st
priority source as boot on
source too.

Philips T Line 65BDL3652T Specifications

General

Brand	Philips
Model	T Line 65BDL3652T
Category	Monitor
Language	English