— 15 —
9 Press EXIT/STATUS to exit from
the menu operations.
If you need to do the auto
programming again
If you move to another place, you may
need to tune the VCR tuner again for
your new residential area.
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select “TUNER SET
UP” then press OK/3.
4 Press 5 or ∞ to select “AUTO
TUNER SET UP” then OK/3.
5 Press 5 or ∞ to select the appropri-
ate TV system [(BG, DK, I) for VR
788/55 and (BG, DK, I, M) for
VR888/55] of your residential area.
6 Press OK/3.
Auto programming starts.
When it ends, programmed channels,
frequencies, and TV systems are
shown on the display.
7 Press EXIT/STATUS to exit from
the menu operations.
Manual Channel Setting
When you want to do channel setting
manually, follow this procedure.
1Select Tuner Set Up Mode
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select “TUNER SET
UP” then press OK/3.
The Tuner Set Up menu appears.
4 Press 5 or ∞ to select “CHANGING
TUNER SET UP” then press OK/3.
The programmed channel informa-
tion list appears with the settings of
the tuned channel flashing. (You can
also watch the picture of the tuned
channel since the list and the picture
alternates on the TV.)
Selecting Colour Mode
Before using the VCR, you need to set
the colour mode both for recording and
playback.
Press COLOUR MODE on the front
panel to change the colour system.
For recording:
AUTO: Normally select this mode.
The colour system is
automatically detected.
NTSC3.58: Select this mode if
“AUTO” does not work well
when recording the NTSC
signals. (For playback on an
NTSC TV)
NTSC4.43: Select this mode if
“AUTO” does not work well
when recording the NTSC
signals on the PAL TV. (For
playback on a PAL TV)
PAL: Select this mode if “AUTO”
does not work well when
recording the PAL signals.
MESECAM:Select this mode if
“AUTO” does not work well
when recording the SECAM
signals.
For playback:
AUTO: Normally select this mode.
When you watch a PAL,
NTSC or MESECAM tape,
the colour system is
automatically detected.
NTSC3.58: Select this mode when
you watch an NTSC3.58
tape on an NTSC TV.
NTSC4.43: Select this mode when
you watch an NTSC4.43
tape on a PAL TV.
NTSC
==
==
=PAL TV: Select this mode
when you watch an
NTSC3.58 tape on a PAL
TV.
PAL: Select this mode if “AUTO”
does not work well when
playing back a PAL tape.
MESECAM:Select this mode if
“AUTO” does not work well
when playing back a
MESECAM tape.
When playing back an NTSC tape with
“AUTO” mode selected
The tape is played back using “NTSC3.58”
mode.
2Select Station
1 Press 5 or ∞ until
an open channel in
which you want to
store a new
channel starts
flashing then press OK/3.
2 Press 5 or ∞ to select the search
starting band.
VHF L: Starts searching from the
VHF L band.
VHF H: Starts searching from the
VHF H band.
UHF: Starts searching from the
UHF band.
3 Press OK/3.
Searching starts, and when a station
is tuned in, searching stops and the
tuned frequency is shown on the TV.
Then the following menu appears.
3Store Channel
Press 5 or ∞ to select “STORE
CHANNEL” then press OK/3.
The programmed channel information
list appears again with the settings of
the newly tuned channel flashing.
• If you do not want to store this station,
select “CONTINUE SEARCH” then
press OK/3, searching starts again.
4Finish Setting
Press EXIT/STATUS.
SELECT CHOOSE /OK
VHF L
VHF H
UHF
TO END PUSH EXIT
SELECT CHOOSE /OK
STORE CHANNEL
CONTINUE SEARCH
TO END PUSH EXIT
VR788/888-55 NEW 6/3/99, 11:50 PM15
To Next Page
Loading...
