Pioneer RX-310 - Tape Copying; High-Speed Copying

BASIC OPERATIONS
TAPE COPYING
1. Load the cassette tape into Deck II.
2. Set Deck | to the stop mode.
3. Use the FUNCTION switch to set to TAPE.
4. Hold down the REC (@) switch first and then press the
PLAY () switch to start erasing.
® Press the STOP/EJECT switch to stop erasing at any
ume.
AUTO-STOP MECHANISM (The Function of both
Decks | and Il)
When the tape is fully wound onto right reel during recording
or playback, the aute-stop mechanism is activated without the
STOP/EJECT switch having to be pressed, and the tape will
automatically stop.
TAPE COPYING
Tape copying is accomplished by playing back the original on
Deck | and recording on Deck II. (Note that the reverse is not
possible.)
If a tape recorded using Dolby NR is copied, the copy as well
will have the same noise-reduction characteristics. Copies of
tapes originally recorded without noise reduction will have no
noise reduction effects.
° Tape copying with added graphic equalizer effects is not
possible.
NORMAL-SPEED COPYING
1. Perform the preliminary operations on page 12.
2. Press the STOP/EJECT switch; then load the original cas-
sette tape into Deck | and the cassette tape to be used for
recording into Deck Il. Close the cassette doors.
(3.Use the FUNCTION switch to set to TAPE.)
* Tape copying is possible regardless of the FUNCTION
switch setting. However, the sound from the speakers
will be that of the program source selected.
4, Press the SYNCHRO switch of the COPY MODE switches.
® The SYNCHRO indicator will light.
§&. Hold down the REC (@) switch and then press the PLAY
(t) switch of Deck Il.
¢ The REC indicator will flash.
® The tape will remain stopped.
NOTE:
Make sure that the SYNCHRO indicator is lit.
ff not lit, the tape cannot be copied; so press the STOP/EJECT
switch, return to item 4 and repeat the operation.
6. Press the PLAY { B») switch of Deck |.
¢ Deck | will start playing back and Deck il will start
recording.
@ The SYNCHRO indicator wil! flash (it will continue to
flash when PAUSE is used with the remote contro!) and
the REC indicator will light.
© Tape copying is unaffected by the volume and graphic
equalizer settings.
e« When setting the FUNCTION switch to TAPE and listen-
ing to playback from Deck |, set the volume and graphic
equalizer controls.
7. To stop while making a copy, press the STOP/EJECT
switches on both decks.
HIGH-SPEED COPYING
1. Perform the preliminary operations on page 12.
2. Press the STOP/EJECT switch; then load the original cas-
sette tape into Deck | and the cassette tape to be used for
recording into Deck Il. Close the casette doors.
3. Press the SYNCHRO switch of the COPY MODE switches.
® The SYNCHRO indicator will light.
© Tape copying is possible regardless of the FUNCTION
switch setting; however, the sound from the speakers
will be that of the selected program source.
4. Press the HIGH SPEED switch of the COPY MODE
switches.
*® The HIGH SPEED indicator will light.
5. Hold down the REC (@) switch and then press the PLAY
(® ) switch of Deck Il.
® The REC indicator will flash.
© The tape will remain stopped.
NOTE:
; Make sure that both the SYNCHRO and HIGH SPEED indicators
are lit. High-speed copying is not possible unless both are lit, so
press the STOP/EJECT switch, return to item 3 and repeat the
operation.
6. Press the PLAY (B®) switch of Deck |.
@ The REC indicator will light.
° The SYNCHRO and HIGH SPEED indicators will flash. It
will continue to flash when PAUSE is used with the re-
mote control.
7. To stop while making a copy, press the STOP/EJECT
switches on both decks.
NOTE:
° When using in the same room as a television set, position far
enough away from the set to avoid interference, or turn off
power to the television set.
° Beat may occur and be included in recordings when copying
while receiving AM broadcasts. in such cases, set the BEAT
CUT switch on the rear panel to the side where beat is less. |
There is no need to operate the BEAT CUT switch except for
AM broadcasts.
When Deck | is stopped while copying, restart from step 6.
When Deck |i is stopped, restart from the beginning.
NOTE:
| Pressing PAUSE from the remote control, operating the Deck | |
switches (except PLAY switch} cancels the Deck If pause mode
and enters the SYNCHRO REC STANDBY mode. Playing Deck
(in this status restarts SYNCHRO REC.
45
<ARB1145>