EasyManua.ls Logo

Pit Boss 77700 - User Manual

Pit Boss 77700
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
 
   
WARNING: Please read the entire manual before installation and use of this electric, pellet fuel burning
appliance. Failure to follow these instructions could result in property damage, bodily injury or even death.
Contact local building or fire officials about restrictions and installation inspection requirements in your area.
ASSEMBLY AND OPERATION INSTRUCTIONS
COPPERHEAD
  
 7
SAVE THESE INSTRUCTIONS! MANUAL MUST BE READ
BEFORE OPERATING!
MODEL : PBV7P1
PART : 77700

Table of Contents

Other manuals for Pit Boss 77700

Preview: Assembly And Operation
Assembly And Operation64 pages

Questions and Answers

  • D
    Dennis HansenSep 12, 2025
    What to do if the temperature is flashing on my Pit Boss Smokers LED screen?
    • M
      Michael MorrisSep 12, 2025
      If the LED screen on your Pit Boss smoker is flashing temperature, it indicates that the grill temperature is below 65°C /150°F, posing a risk that the fire could go out. To resolve this, check the hopper for sufficient fuel and inspect the feed system for obstructions. Remove pellets and follow the Care and Maintenance instructions. Also, inspect the grill temperature probe, cleaning it if dirty according to the Care and Maintenance instructions. Ensure the burn pot is free of ash build-up or obstructions, following the Care and Maintenance instructions. Verify the fan is working correctly and the air intake is not blocked, cleaning it if necessary. Finally, check the auger motor to confirm it's rotating and that there's no blockage in the auger tube.
  • I
    icalderonAug 27, 2025
    What does ErH error code mean on Pit Boss 77700?
    • T
      theresa15Aug 27, 2025
      If your Pit Boss smoker displays an "ErH" error code, it indicates the smoker has overheated, possibly due to a grease fire or excess fuel. To resolve this, press and hold the Power Button to turn the unit off and allow the smoker to cool down. Follow the Care and Maintenance instructions. After maintenance, remove the pellets and confirm the positioning of all component parts. Once cooled, press the Power Button to turn the unit on, then select the desired temperature. If the error code persists, contact Customer Service.
  • S
    Sarah WilliamsSep 9, 2025
    What does the 'noP' error code mean on my Pit Boss Smokers?
    • A
      Allison NelsonSep 9, 2025
      If you see a 'noP' error code on your Pit Boss Smoker, it indicates a problem with the meat probe connection. First, disconnect the meat probe from the connection port on the control board, and then reconnect it, ensuring the meat probe adapter is firmly connected. Check for any signs of damage to the adapter end. If the error persists, check the meat probe wires for any damage. If damaged, contact Customer Service for a replacement part. If the issue continues, the control board may be faulty, and you should contact Customer Service for a replacement part.
  • D
    Daniel CarrilloSep 7, 2025
    What does 'Er1' error code mean on my Pit Boss Smoker?
    • S
      stephaniemanningSep 7, 2025
      If you see an 'Er1' error code on your Pit Boss Smoker, it means the temperature probe wire is not making a connection. Access the electrical components on the base of the unit (see Electric Wire Diagram) and check for any damage to the temperature probe wires. Ensure the temperature probe spade connectors are firmly connected, and connected correctly, to the control board.
  • A
    Alexandra TaylorSep 5, 2025
    What does it mean if I see flashing dots on the LED screen of my Pit Boss Smoker?
    • D
      David LopezSep 5, 2025
      Flashing dots on the LED screen of your Pit Boss Smoker indicate that the unit has power and is in start-up mode, meaning the igniter is on. This is not an error. The igniter will turn off after five minutes, and once the flashing dots disappear, the unit will begin to adjust to the selected temperature.
  • A
    Aaron TurnerSep 3, 2025
    What to do if I see 'ErH' error code on my Pit Boss Smoker?
    • E
      Elizabeth WhiteSep 3, 2025
      If you see an 'ErH' error code on your Pit Boss Smoker, it indicates that the smoker has overheated, possibly due to a grease fire or excess fuel. Press and hold the power button to turn the unit off and allow it to cool completely. Then, follow the care and maintenance instructions. After maintenance, remove the pellets and confirm the correct positioning of all component parts. Once the unit is cooled, press the power button to turn it on again, and select your desired temperature. If the error code is still displayed, contact Customer Service.
  • M
    Mary AriasSep 2, 2025
    What to do if my Pit Boss Smoker has no power lights on the control board?
    • J
      Jenna GregorySep 2, 2025
      If there are no power lights on the control board of your Pit Boss Smoker, start by pressing the power button, holding it for two seconds to ensure a solid connection. Then, verify that the smoker is properly plugged into a working power source and that the GFCI outlet hasn't tripped; reset the breaker if needed, and ensure the GFCI is a minimum 10 Amp service. Check that all wire connections are firmly connected and dry. If the issue persists, the fuse on the control board may be blown; remove cooking components, turn the unit on its side, remove the screws on the rear of the control board, and inspect the fuse for breaks or blackening, replacing it if necessary. If none of these steps work, the control board may be faulty, and you should contact Customer Service for a replacement.
  • M
    Michael NguyenAug 31, 2025
    What does noP error code mean on Pit Boss 77700 Smokers?
    • P
      Paul PowersAug 31, 2025
      If your Pit Boss smoker displays a "noP" error code, it could be due to several reasons related to the meat probe. First, disconnect the meat probe from the connection port on the Control Board and reconnect it, ensuring the adapter is firmly connected and checking for damage. If the issue persists, inspect the meat probe wires for damage. If the problem continues, the Control Board may be faulty and needs to be replaced.
  • C
    Christopher PowellAug 30, 2025
    What does Er1 error code mean on Pit Boss 77700?
    • N
      nicolespenceAug 30, 2025
      If your Pit Boss smoker displays an "Er1" error code, it indicates that the temperature probe wire is not making a connection. To fix this, access the electrical components on the base of the unit (see Electric Wire Diagram) and check for any damage to the Temperature Probe wires. Ensure the Temperature Probe spade connectors are firmly connected, and connected correctly, to the Control Board.
  • K
    Kelli BlackAug 29, 2025
    How to fix frequent flare-ups in my Pit Boss Smoker?
    • C
      carlosgarciaAug 29, 2025
      Frequent flare-ups in your Pit Boss Smoker may be due to the cooking temperature being too high. Try cooking at a lower temperature, keeping it under 176°C / 350°F when cooking greasy foods, as grease has a flash point. Also, flare-ups can occur due to grease build-up on cooking components, so follow the care and maintenance instructions to clean them.

Pit Boss 77700 Specifications

General IconGeneral
BrandPit Boss
Model77700
CategorySmokers
LanguageEnglish

Related product manuals