Pit Boss PB820CS1 - User Manual

Questions and Answers

J
John PhillipsAug 21, 2025
What to do if my Pit Boss Grill will not achieve or maintain stable temperature?
- J
  Jessica RitterAug 21, 2025
  If your Pit Boss Grill is not achieving or maintaining a stable temperature, consider these potential causes: insufficient airflow through the burn pot due to ash build-up or obstructions—check the burn pot and clean as needed, ensure the fan is working properly and the air intake isn't blocked, and confirm the auger motor's operation without blockages. Start the grill at COOK temperature to SMOKE and wait 10 minutes, checking that the flame produced is bright and vibrant. Also, check for a lack of fuel, poor fuel quality, or obstructions in the feed system. Ensure the hopper has sufficient fuel, and if the pellets are of poor quality or too long, remove them. Lastly, check the status of the grill probe, cleaning it if dirty.
J
James BranchAug 23, 2025
Why is my Pit Boss PB820CS1 Grill producing excess or discolored smoke?
- W
  William HallAug 25, 2025
  Excessive or discolored smoke from your Pit Boss Grill can stem from several factors. Grease build-up is a common cause, so follow the care and maintenance instructions to address this. The quality of the wood pellets can also be a factor; remove any moist pellets from the hopper, clean it out, and replace with dry wood pellets. A blocked burn pot due to moist wood pellets is another possibility; clear the burn pot and follow the Hopper Priming Procedure. Lastly, ensure sufficient air intake for the fan by checking that it is working properly and the air intake is not blocked, cleaning if necessary.
B
Brett RobertsAug 26, 2025
What does Err Error Code with IGNITOR Icon Blinking mean on Pit Boss Grill?
- M
  Monica FrankAug 26, 2025
  The Err Error Code with the IGNITOR icon blinking on your Pit Boss Grill means the ignitor is not working properly or not making a connection, or the ignitor has failed. Remove cooking components and turn the unit on to inspect the igniter, visually confirming that it is working by feeling for heat above the burn grate and that the igniter is aligned with the hole in the burn grate and open to light the pellets. If it's not operating properly, contact Customer Service. The igniter may need to be replaced, so contact Customer Service for a replacement part.
K
Kenneth MasonAug 28, 2025
What to do if Pit Boss PB820CS1 Grill temperature on SMOKE is too high?
- J
  Jacqueline DuncanAug 28, 2025
  If the grill temperature on the SMOKE setting is too high, the "P" setting may be too low. Push the "P" SET button and increase the "P" setting value.
T
Thomas HernandezAug 30, 2025
Why are there no power lights on my Pit Boss PB820CS1 Grill control board?
- J
  Jillian PrinceAug 30, 2025
  If there are no power lights on the control board of your Pit Boss Grill, several issues could be the cause. First, ensure the unit is properly plugged into a working power source and reset the breaker. Check that the GFCI is a minimum 15 Amp service. Also, make sure all wire connections are firmly connected and dry. Another potential cause is a blown fuse on the control board, which would need to be manually replaced. The GFCI outlet may have been tripped. In that case, check wire connections to ensure they are firmly connected and dry and that the GFCI is a minimum 15 Amp service. Finally, a faulty control board may be the reason, requiring a replacement.
D
David Miller MDSep 1, 2025
What does ErL Error Code mean on Pit Boss Grill?
- T
  Tracy KnappSep 1, 2025
  The ErL error code on your Pit Boss Grill indicates that the grill failed to perform the start-up cycle. You can resolve it by checking the proper positioning of cooking components, ensuring the hopper has sufficient fuel and that there are no obstructions in the feed system. Check the grill probe to confirm if the actual temperature is correct and accurate, cleaning it if dirty. Also, check the ignitor positioning and that it is heating up properly. In extreme cold, the grill may require a second start. Check the fan to ensure it is working properly.
A
Angela SantosSep 3, 2025
What does Err Error Code with PELLET Icon Blinking mean on Pit Boss PB820CS1?
- T
  Tony HuertaSep 3, 2025
  The Err Error Code with the PELLET icon blinking on your Pit Boss grill indicates a lack of fuel, poor fuel quality, an obstruction in the feed system, or a jammed auger. Check the hopper to ensure the fuel level is sufficient, and replenish if low. If the wood pellets are of poor quality or too long, remove them.
M
marcia54Sep 5, 2025
How to prevent frequent flare-ups on my Pit Boss Grill?
- K
  Kim FernandezSep 5, 2025
  To prevent frequent flare-ups on your Pit Boss Grill, try cooking at a lower temperature, keeping it under 176°C / 350°F when cooking highly greasy food, as grease has a flash point. Also, make sure to address any grease build-up on cooking components.
D
Danielle HoffmanSep 7, 2025
What does Err Error Code with AUGER Icon Blinking mean on Pit Boss PB820CS1 Grill?
- M
  morenojenniferSep 7, 2025
  The Err Error Code with the AUGER icon blinking on your Pit Boss Grill indicates that the auger is not primed or the auger motor is jammed. If the unit is new or the hopper was completely emptied, the auger must be primed to allow pellets to fill the feed system. Remove cooking components and turn the unit on to inspect the auger feed system, visually confirming that the auger is dropping pellets into the burn pot. If it's not operating properly, contact Customer Service.
H
Heather JohnsonSep 10, 2025
What does Err Error Code with FAN Icon Blinking mean on Pit Boss PB820CS1?
- C
  Christine SmithSep 10, 2025
  The Err Error Code with the FAN icon blinking on your Pit Boss Grill indicates that the fan is not working properly or not making a connection. Check the fan to ensure it is working properly and the air intake is not blocked. Check for any damage to the fan wires. Clean the fan blades if they are dirty.

Summary

Grill Safety Information

Grill Dangers and Warnings

Key safety precautions and potential hazards associated with grill operation and installation.

Wood Pellet Fuel Guide

Carbon Monoxide Safety

Grill Operating Instructions

Grill Setup and Environment

Guidelines for optimal grill placement, considering weather conditions for best performance.

Grill Temperature Settings

Explanation of temperature settings, their uses, and factors affecting grill temperature accuracy.

Control Board Overview

Detailed explanation of the digital control board, its functions, and displays for operation.

Hopper Priming Procedure

Steps to prime the auger system for first-time ignition and after pellet depletion.

Smoke iT App Connectivity

Automatic Start-Up

Grill Care and Maintenance

Internal Grill Cleaning

Wood Pellet Fuel Guide

Grill Cooking Guidelines

Poultry Cooking Guidelines

Pork Cooking Guidelines

Beef Cooking Guidelines

Grilling Tips and Techniques

Food Safety Practices

Essential food safety practices for preparing and handling food during grilling.

Advanced Grilling Techniques

Advanced grilling techniques for flavor enhancement, moisture retention, and preventing flare-ups.

Grill Troubleshooting Guide

Troubleshooting Common Issues

Troubleshooting common issues like no power, fire failure, temperature problems, and error codes.

Electrical Wire Diagram

Grill Warranty Information

Pit Boss PB820CS1 Specifications

General

Grill Category	Pellet Grill
Type	Freestanding
Cooking Area	820 sq in
Temperature Range	180°F to 500°F
Hopper Capacity	21 lbs
Wi-Fi Capability	No
Material	Steel
Fuel Type	Wood Pellets
Warranty	5 Years
Ignition Type	Automatic