14/42
Response time upon unlocking the actuator:
typically 7 ms, max. 12 ms
Response time upon removal of the actuator:
typically 120 ms, max. 200 ms
Maximum EDM signal status change delay: 500 ms
8.3.4 Electrical data of O3/O4 signalling outputs
Rated operating voltage U
e3
: 24 Vdc
Output type: PNP
Maximum current per output I
e3
: 0.1 A
Utilization category: DC13; U
e3
=24 Vdc, I
e3
=0.1 A
Short circuit detection: No
Overvoltage protection Yes
Internal self-resettable protection fuse:
1.1 A
8.3.5 RFID sensor data
Assured operating distance S
ao
: 2 mm
Assured release distance S
ar
: Mode 1:
6 mm (actuator not locked)
10 mm (actuator locked)
Modes 2 and 3:
10 mm (actuator locked and not locked)
Rated operating distance S
n
: 3 mm
Repeat accuracy: ≤ 10 % s
n
Differential travel: ≤20 % s
n
RFID transponder frequency: 125 kHz
Max. switching frequency: 1 Hz
Minimum distance between 2 identical de-
vices to avoid reciprocal radio interferences: 0 mm
8.4 Technical data of the integrated control devices
8.4.1 General data
Protection degree: IP65 acc. to EN 60529
Mechanical endurance:
- Spring-return button: 1 million operating cycles
- Emergency stop button: 50,000 operating cycles
- Selector switch: 300,000 operating cycles
- Key selector switch: 50,000 operating cycles
30,000 operating cycles including re-
moval of the key
Safety parameter B
10D
: 130,000 (emergency stop button)
8.4.2 Actuating force
Spring-return button: min. 4 N max. 100 N
Emergency stop button: min. 20 N max. 100 N
Selector switch: min. 0.1 Nm max. 1.5 Nm
Key selector switch: min. 0.1 Nm max. 1.3 Nm
8.4.3 Contact block
Material of the contacts: silver contacts
Contact type:
Self-cleaning contacts with double inter-
ruption
8.4.4 Electrical data
Thermal current (I
th
): 1 A
Rated insulation voltage (U
i
): 32 Vac/dc
Rated impulse withstand voltage (U
imp
):
1.5 kV
LED supply voltage: 24 Vdc ± 15%
LED supply current: 12 mA per LED
8.4.5 Utilization category of the contact block
Direct current: DC-13 U
e
= 24 V I
e
= 0.55 A
8.4.6 M12 connector electrical data
Max. operating current/voltage: 32 Vac/dc max. 1.5 A
8.4.7 M23 connector electrical data
Max. operating current/voltage: 32 Vac/dc max. 3 A
8.5 In compliance with standards
EN ISO 14119, EN 60947-5-3, EN 60947-1, EN 60204-1, EN ISO 12100, EN 60529,
EN 61000-6-2, EN 61000-6-3, EN 61508-1, EN 61508-2, EN 61508-3, EN ISO 13849-1,
EN ISO 13849-2, EN IEC 62061, EN 61326-1, EN 61326-3-1, EN IEC 63000, ETSI 301 489-1,
ETSI 301 489-3, ETSI 300 330, UL 508, CSA C22.2 No. 14
8.6 In compliance with Directives
Machinery Directive 2006/42/EC, EMC Directive 2014/30/EU, Radio Equipment Direc-
tive 2014/53/EU, RoHS Directive 2011/65/EU
FCC Part 15 Statements: This device complies with part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including in-
terference that may cause undesired operation.
9 SPECIAL VERSIONS ON REQUEST
Special versions of the device are available on request.
The special versions may differ substantially from the indications in this instruction
sheet.
The installer must ensure that he has received written information from the support
service regarding installation and use of the special version requested.
10 DISPOSAL
At the end of its service life, the product must be disposed of properly, accord-
ing to the rules in force in the country in which the disposal takes place.
11 SUPPORT
The device can be used for safeguarding people’s physical safety, therefore in case
of any doubt concerning installation or operation methods, always contact our tech-
nical support service:
Pizzato Elettrica Srl
Via Torino, 1 - 36063 Marostica (VI) - ITALY
Telephone +39.0424.470.930
E-mail tech@pizzato.com
www.pizzato.com
Our support service provides assistance in Italian and English.
12 EC DECLARATION OF CONFORMITY
I, the undersigned, as a representative of the following manufacturer:
Pizzato Elettrica Srl - Via Torino, 1 - 36063 Marostica (VI) – ITALY
hereby declare that the product is in conformity with whatever prescribed by the
2006/42/EC Machine Directive. The complete version of the present conformity dec-
laration is available on our website www.pizzato.com
Marco Pizzato
DISCLAIMER:
Subject to modifications without prior notice and errors excepted. The data given in
this sheet are accurately checked and refer to typical mass production values. The de-
vice descriptions and its applications, the fields of application, the external control de-
tails, as well as information on installation and operation, are provided to the best of
our knowledge. This does not in any way mean that the characteristics described may
entail legal liabilities extending beyond the “General Terms of Sale”, as stated in the
Pizzato Elettrica general catalogue. Customers/users are not absolved from the obli-
gation to read and understand our information and recommendations and pertinent
technical standards, before using the products for their own purposes. Taking into ac-
count the great variety of applications and possible connections of the device, the ex-
amples and diagrams given in the present manual are to be considered as merely de-
scriptive; the user is deemed responsible for checking that the specific application of
the device complies with current standards. This document is a translation of the orig-
inal instructions. In case of discrepancy between the present sheet and the original
copy, the Italian version shall prevail. All rights to the contents of this publication are
reserved in accordance with current legislation on the protection of intellectual prop-
erty. The reproduction, publication, distribution and modification, total or partial, of all
or part of the original material contained therein (including, but not limited to, texts,
images, graphics), whether on paper or in electronic form, are expressly prohibited
without written permission from Pizzato Elettrica Srl.
All rights reserved. © 2024 Copyright Pizzato Elettrica
To Next Page
Loading...