Planmeca ProMax 3D Max with ProTouch - User Manual

234 pages

Save Page as PDF

To Next Page

Planmeca ProMax

3D Max with ProTouch

technical manual

1003480210034802

Main Page

Table of Contents3
General and Technical Data7
Introduction7
Manual Versions7
Associated Documentation7
Training7
Warnings and Cautions8
Symbols on Product Labels9
Technical Data for Planmeca Promax Product Family10
User's Statement14
Radiation Leakage Technique Factors14
Filtration14
Maximum Attenuation Equivalent of the Front Panel of the 3D Sensor Head15
Rated Line Voltage15
Maximum Line Current15
Technique Factors that Constitute the Maximum Line Current Condition15
Generator Rating and Duty Cycle15
Maximum Deviation of Peak Tube Potential from Indicated Value15
Maximum Deviation of Tube Current from Indicated Value15
Maximum Deviation of Exposure Time from Indicated Value15
Definition of Measurement Criteria15
CTDI Values (96 Kv Tube)25
CTDI Values (120 Kv Tube)28
Air Kerma31
Stray Radiation Measurements32
Handling Precautions for Pcbs and Software Chips34
Handling Printed Circuit Boards34
Handling Software Flash Memory Chips35
EMC Information35
User Interface40
Switches and Buttons40
On/Off Switch40
Emergency Button40
Patient Positioning Controls41
Adjusting Exposure Sound Volume Level42
Touch Screen45
Overview45
Calibrating Touch Screen Display46
Information Displays47
Entering Additional Settings Menus47
Network Settings (1400)48
Main Network Settings49
Sensor Network Settings49
Proceph Network Settings50
Network Settings Reset51
Resetting X-Ray Unit IP Address51
Resetting 3D Sensor IP Address52
Clinic Management Settings56
Technical Settings57
Entering Technical Settings Menu57
Configuring Unit Settings57
Performing Filament Definition62
Entering Calibrations Menu63
Setting Parameter Limits63
Checking Exposure Statistics65
Clearing Error History66
Setting Maintenance Reminder66
Changing X-Ray Unit Mode67
Diagnostics and Troubleshooting69
Showing Component Information69
Log Management71
Testing Ethernet Mode72
Testing Communication between X-Ray Unit Components73
Running Diagnostics76
Input Connections79
Input Connections (INP2)80
Input Connections (Ed2/Ed3)80
Help and Error Messages81
Help Messages81
Error Messages83
Motorised Motion Related Errors (E2Xx)84
X-Ray Generation Related Errors (E3Xx)88
Feedback Errors (E4Xx)89
Communication Errors (E6Xx)92
Calibration Errors (E7Xx)93
System Conflicts (E8Xx)94
Infrastructure Errors (E9Xx)95
Preventive Maintenance97
System Maintenance97
Cleaning97
Operating Checks97
Preventive Maintenance Checks98
General98
X-Ray Unit Adjustments and Quality Control Checks99
X-Ray Tube Feedback System100
Electrical Safety Measurements102
Mechanical Checks104
Column Motor Nut104
Cephalostat Ear Posts Fluent Motion105
Panoramic and 3D Calibrations106
Required Calibration Tools107
Adjusting Panoramic Beam and Patient Positioning Mechanism109
Recommended Adjustment Procedures110
Adjusting Smartpan Beam Position110
Adjusting Collimator Angle112
Calibrating Angle Sensors121
Calibrating Patient Support Table Movements127
Calibrations130
Smartpan Beam Check and Sensor Flat Field Calibration132
Patient Positioning Table and Positioning Lights Adjustment132
Taking Ball Phantom Exposure137
Panoramic Mode Patient Positioning Lights148
Traditional Adjustment Procedures157
Adjusting Smartpan Beam Position158
Adjusting Collimator Angle158
Adjusting Patient Positioning Mechanism158
Calibrating Patient Support Table Movements170
Calibrating Angle Sensors170
Smartpan Beam Check and Sensor Flat Field Calibration170
Taking Ball Phantom Exposure170
Panoramic Mode Patient Positioning Lights171
Adjusting 3D Lights Position171
Calibrations178
Patient Support Arm181
Removing Covers181
Removing Patient Support Table Cover181
Detaching User Interface and Support Arm Lower Cover182
Replacing Patient Position Control PCB182
Adjusting Arm Tilt184
Adjusting Lift Screw184
Column Adjustments186
Adjusting Telescopic Column Position186
Calibrating Column Motor Position Sensor188
Setting Column Maximum Height190
Setting Column Motor Maximum Speed191
Calibrating Patient Support Sensor192
Adjusting Patient Support Optical Sensor194
Adjusting Patient Support Safety Switch196
Parts Replacement and Repair197
Removing and Replacing Covers197
Removing Sensor Covers197
Removing C-Arm Upper Covers199
Removing C-Arm Inner Cover200
Removing Tube Head Covers (96 Kv Tube)200
Removing Tube Head Covers (120 Kv Tube)202
Removing Shoulder Arm Covers205
Removing Patient Support Arm Covers206
Removing Column Covers206
Removing and Replacing Pcbs212
Replacing Column Pcbs212
Removing Patient Position Control PCB219
Replacing / Upgrading Software219
Replacing Power Cable219
Replacing Other Components221
Replacing Column Battery on RTC PCB221
Appendix A: Diagrams222
Input PCB222
Ed3 New Input2 Wiring Diagram223
Ed2 Input Module Wiring Diagram224
CPU1 PCB Wiring Diagram225
C-Arms Pcbs226
C-Arm PCB Wiring Diagram226
C-Arm PCB (120 Kv Tube Head) Wiring Diagram227
PPC PCB Wiring Diagram228
PSU PCB Wiring Diagram229
Ethernet PCB Wiring Diagram230
Cephalostat Pcbs231
Planmeca Promax Ceph PCB Wiring Diagram231
Planmeca Proceph PCB Wiring Diagram232

Brand	Planmeca
Model	ProMax 3D Max with ProTouch
Category	Medical Equipment
Language	English

Planmeca ProMax 3D Max with ProTouch - User Manual

Table of Contents

Planmeca ProMax 3D Max with ProTouch Specifications

Related product manuals