1
2
3
4
SYMPTOM CAUSE SOLUTION
Motor fails to
start or kicks
on and off
A Pump transformer must be plugged into a grounded power outlet.
No or slow
water flow
through the
return fitting.
Filter pump is
not cleaning
the pool
properly(Cloudy
water,
green…..etc.)
Water leakage
A Fill the pool to the fill line. The suction fitting must be at least 4” under water.
A Maintain chlorine level between 1.0 to 1.6 ppm.
B Maintain pH level between 7.3 to 7.8.
C Clean or replace the filter cartridge.
A Tighten the hose clamps. Check the o-rings on the suction/return fittings.
Check hoses for damage. Replace if needed.
D Check filter for damage and holes. Replace new filter immediately.
E Check for obstructions(s) at the suction fitting and return fitting.
F Have the pool water sample tested by a pool supply store. Obtain opinions
on additional water treatment chemicals.
G Run pump more often, but never when the pump is in use. Clean/replace
filter cartridge more frequently.
B Check for obstructions(s) at the suction fitting and return fitting.
A Pump transformer not
plugged in
B Check the line voltage, it must be in the range of 215V to 245V (See product label).B Low voltage
A Low pool water level
A Chlorine level
B pH level
C Dirty filter cartridge
D Damaged filter
cartridge
E Slow water flow
F Other chemicals
required
G Pool water very dirty
B Inlet/Outlet clogged
C Dirty filter cartridge
A Suction/return hose
B Vent screw in Seal Top
C Seal Top
D Baes
C Clean or replace the filter cartridge. A spare cartridge makes service more
convenient.
B Check O-ring 9 for damage. Replace if needed. Tighen the Vent Screw 8 .
C Check O-ring 12 for damage. Replace if needed. Tighten the Seal Top 10 .
D Check O-ring 12 for damage. Replace if needed. Tighten the Base 11 .
2. To depressurize the Filter Pump system, vent the filter pump by twisting the Vent Screw 8 counter-clockwise.
3. Loosen the Hose Clamps 6 at the filter pump inlet and outlet. Detach both Hoses 5 from the filter pump.
4. Turn the filter pump up-side-down. The Base 11 is now locked by a latch pin. To release the lock, push the latch pin down and then turn left. Detach the Base
11 from the Canister 13 by turning counter-clockwise.
5. Remove the Base 11 from the Canister 15 .
6. Remove the Motor Assembly 15 from the Canister 13 . Be careful not
to lose the rubber Nozzle 14 .
14
15
TROUBLESHOOTING GUIDE ROTOR REPLACEMENT INSTRUCTION
POOL PUMP DISASSEMBLY & STORAGE
15
13
11
15
13
11
13
15
11
1. Unplug the Power Filter Pump. Remove the Flow Diverter 3 ,Suction Fitting Screen 2 and Suction Fitting Base 1 from the Return Fitting and Suction Fitting
and flow plug with Plug 4 .
2. Slowly unscrew the Vent Screw 8 from the Seal Top 10 allowing the Filter Pump to depressurize.
3. Remove the Seal Top 10 by turning counter-clockwise.
4. Remove the Filter Cartridge 16 and remove any chlorine tablets left inside the core section of the filter.
5. Loosen all four Hose Clamps 6 , remove the Hoses 5 and allow water to drain out.
6. Clean and dry all filter pump parts including filter cartridges.
7. Liberally lubricate the O-rings 9 at the Seal Top 10 and Gasket 12 on the Canister 13 with petroleum jelly, and then reassemble it along with the Seal Top 10 ,
Vent Screw 8 onto the Canister 13 . Store all parts carefully. In a airtight plastic bag.
1. Unplug the Power Filter Pump. Remove the Flow Diverter 3 ,Suction Fitting Screen 2 and Suction Fitting Base 1 from the Return Fitting and Suction Fitting
and flow plug with Plug 4 .
WARNING: UNPLUG THE POWER CORD BEFORE TROUBLESHOOTING THE FILTER PUMP.
14 15
OWNER’S MANUAL
To Next Page
Loading...
Need help?
General
