What to do if my Qlima Heat Pump stops working without an error code?
If your Qlima Heat Pump stops working without displaying an error code, it could be due to insufficient water in the heat exchanger. Check your water circuit operation to ensure adequate water flow. Alternatively, the control panel might be defective, requiring replacement.
Why does my Qlima SPHP 130 have low pressure protection?
Low pressure protection in your Qlima Heat Pump can occur due to several reasons. It might be caused by insufficient refrigerant gas, in which case you should recharge the refrigerant gas. Another possible cause is a pressure switch that isn't connected well or is defective; try connecting or replacing the pressure switch. Lastly, a defective control panel could also trigger this issue, necessitating its replacement.
What to do if my Qlima SPHP 130 Heat Pump flow sensor malfunctions?
If the flow sensor in your Qlima Heat Pump malfunctions, it could be due to insufficient water in the heat exchanger; in this case, you should check your water circuit operation. It may also indicate a defective water flow sensor, which would require replacing the water flow switch, or a defective control panel, which would also require replacement.
How to fix Qlima SPHP 130 Heat Pump water intake temperature sensor malfunction?
A malfunction in the water intake temperature sensor of your Qlima Heat Pump can stem from a few potential issues. First, check if the sensor is badly connected and, if so, reconnect it. If the sensor is defective, it will need to be replaced. Lastly, a defective control panel could also be the root cause, requiring its replacement.
What to do if Qlima Heat Pump stops working without error code?
If the Qlima Heat Pump unit stops working without an error code, it might be due to insufficient water in the heat exchanger. You should check your water circuit operation. Alternatively, the control panel could be defective, requiring replacement.
What to do if Qlima Heat Pump shows flow sensor malfunction?
If your Qlima Heat Pump displays a flow sensor malfunction, it could be due to insufficient water in the heat exchanger. Check your water circuit operation. Alternatively, the water flow sensor or the control panel may be defective, requiring replacement.
Why is my Qlima Heat Pump showing low pressure protection?
If your Qlima Heat Pump is showing a low pressure protection error, this could be due to insufficient refrigerant gas, in which case you should recharge the refrigerant gas. Another cause could be a pressure switch that is not well connected or defective, so connect or replace the pressure switch. Finally, the control panel might be defective and need replacing.
What causes water intake temperature sensor malfunction in Qlima Heat Pump?
If your Qlima Heat Pump's water intake temperature sensor malfunctions, it could be due to a badly connected sensor, in which case you should reconnect it. Alternatively, the sensor or the control panel may be defective, requiring replacement.
Why is antifreeze protection activated on my Qlima Heat Pump?
The antifreeze protection on your Qlima Heat Pump activates when the ambient temperature is too low. No intervention is necessary.
General| Best uses | - |
|---|---|
| Control type | Buttons |
| Product type | Electric pool heater |
| Product color | Blue |
| Easy to install | Yes |
| Buttons quantity | 4 |
| Pool capacity (max) | 16000 L |
| Pool capacity (min) | - L |
| Units of measurement | °C |
| Maximum heating capacity | 2.8 °C/h |
| Minimum pumping capacity | 2 m³/h |
| Temperature measurement range | 15 - 40 °C |
| Coefficient of performance (COP) | 4.83 |
| International Protection (IP) code | IPX4 |
| Operating temperature (T-T) | 8 - 43 °C |
| Motor power | 580 W |
| Input voltage | 220 - 240 V |
| Input frequency | 50 Hz |
Weight and Dimensions| Depth | 400 mm |
|---|---|
| Width | 385 mm |
| Height | 280 mm |
| Weight | 18000 g |
Lists all items included in the product packaging.
Guidelines for safe and effective operation of the heat pump.
Procedures and precautions for cleaning the heat pump unit.
Recommendations for maintaining pool water chemistry for optimal performance.
Diagram showing the recommended installation configuration.
Steps for connecting the water pipes to the heat pump.
Instructions for safely connecting the heat pump to the power supply.
Details the functions of each button and display element on the control panel.
Instructions for setting and operating the heating mode.
Explains how the heating mode functions and its parameters.
Information on accessing and modifying advanced system settings.
Specifies the environmental conditions required for normal operation.
Checks to perform before activating the heat pump.
Sequence of actions to start and operate the heat pump.
Instructions for cleaning the heat pump's exterior and components.
Recommended annual service checks by a qualified person.
Advice on how to store the heat pump during the winter season.
Lists common error codes, possible causes, and corrective actions.
To Next Page
