QSC KC12 - Page 20

20
EQ: Adjust the 4-band, parametric equalizer.
• Use the scroll wheel to navigate a desired EQ band. Press the Enter button, and then use the
Selector Knob to adjust. When you are finished, press the Enter button to make the change, or
the Exit button to exit without changing the parameter.
dB Hz Q
High Shelving Band
(Default)
0.0 dB to -6.0 dB
(0.0 dB)
1.0 kHz to 10.0 kHz
(8 kHz)
N/A
EQ1 (EQ for Band 1)
(Default)
0.0 dB to -6.0 dB
(0.0dB)
50 Hz to 20.0 kHz
(0.0 Hz)
0.4 to 4.0
(0.7)
EQ2 (EQ for Band 2)
(Default)
0.0 dB to -6.0 dB
(0.0 dB)
200 Hz to 20.0 kHz
(0.0 Hz)
0.4 to 4.0
(0.7)
Low Shelving Band
(Default)
0.0 dB to -6.0 dB
(0.0 dB)
100 Hz to 500 Hz
(0.0 Hz)
N/A
• EQ IN/OUT – Engages/bypasses the equalizer
• RESET – Returns the EQ to the default settings.
ROOM DELAY: Adjust the signal delay for rear fill and similar applications.
• 0 - 200 milliseconds, 0 - 226 feet , 0 - 68 meters
• All units of measure change together when the Selector knob is turned.
BLUETOOTH MENU: The menu for pairing Bluetooth-compatible host devices and connecting
multiple KC12 loudspeakers. For steps on how to pair Bluetooth host devices or connecting multiple KC12 loudspeakers together, see
"Using Bluetooth" on page 22.
• STATUS – Displays “PAIR” if the KC12 is not paired, or “PAIRED” if the KC12 is paired to a host
device.
• MULTI – Displays “LINK” if the KC12 is not connected to additional KC12 loudspeakers, or
“LINKED” if connected to additional KC12 loudspeakers.
• ST ASSIGN – Assigns each KC12 loudspeaker to produce either the LEFT or RIGHT channel of
the Bluetooth Stereo signal or sum the stereo channels to MONO (default).
• SYNC TONE – When Bluetooth is paired to or unpaired from a host device or when a KC12 is connected to additional KC12
loudspeakers for True Wireless Stereo or Multicast pairing, the KC12 will play a sync tone to notify the user of a
change in status. That tone can be left ON (default) or turned OFF to not disrupt your event, in case the Bluetooth
connection is intermittent.
• RESET BT – Resets all Bluetooth Menu settings to factory default and removes all paired host devices and connected/linked
loudspeakers back to factory default state. After a RESET, you will need to ‘discard’ the KC12 Bluetooth connection in
the host device’s Bluetooth settings before attempting to pair again the host device to the KC12 loudspeaker.
• DISCONNECT – Disconnects all paired host devices and MULTI linked KC12 loudspeakers. This function does not clear the memory
of paired host devices, and therefore, the auto-pair functionality will still be available for previously paired host
devices once KC12 loudspeakers are put into LINKED mode again.
OUTPUT MENU: ASSIGN OUTPUT B can be utilized as a customizable output, sending only the select-able channels to the output
depending on your application needs.
NOTE: This output is post-DSP, so some latency will occur (<1ms) from IN to THRU.
For direct pass-THRU that is not affected by system processing, use Channel A IN
andTHRU.
• A+B+C+BLUETOOTH – All channels are sent from the output (including Bluetooth), POST-DSP
EQ
HIGH
EQ1
EQ2
LOW
dB
0.0
0.0
0.0
Q
0.7
0.7
0.0
Hz
1.0K
50.0
200.0
100.0
EQ OUT RESET
ROOM DELAY
0.0
0.0
0.0
MS
FEET
METERS
BLUETOOTH
STATUS
MULTI
ASSIGN
TONE
PAIR
LINK
MONO
DISCONNECT
RESET
ON
ASSIGN OUTPUTS
A+B+C+BLUETOOTH
A+B+C
B THRU
EXT SUB: DELAY OFF
LEVEL: UNITY