Why RAMSET RAM 100 doesn't open?
Your RAMSET Gate Opener might not be opening due to several reasons: * The Radio L.E.D. is ‘On’ (refer to related solutions). * A 10 amp fuse might be blown; check and replace it if necessary. * The opening accessory might not be functioning; check or replace it.
What to do if “REv LOOP” L.E.D. always ‘on’ in RAMSET RAM 100?
If the “Rev Loop” L.E.D. is always ‘On’ on your RAMSET Gate Opener, disconnect all accessories, including plug-ins, using the “Rev Loop” input. If problem persist, contact Ramset.
What to do if the “EXIT” L.E.D. is always ‘on’ on RAMSET RAM 100 Gate Opener?
If the “EXIT” L.E.D. is always ‘On’ on your RAMSET Gate Opener, disconnect all accessories, including plug-ins, using the “Exit” input. If the problem persists, contact Ramset.
What to do if “RADIO” L.E.D. is always ‘on’ on RAMSET RAM 100 Gate Opener?
If the “RADIO” L.E.D. is always ‘On’ on your RAMSET Gate Opener: * Check all transmitters for a stuck button. * Remove the receiver. If the problem persists, contact Ramset.
How to troubleshoot RAMSET Gate Opener when no lights are ‘on’?
If no lights are ‘On’ on your RAMSET Gate Opener: * Check if the circuit breaker has popped and reset it. * See if the 1/2 amp fuse is blown and replace it. * The power supply on the Control Board might be damaged; in this case, return the Control Board for repair.
What to do if my RAMSET gate opener automatically opens, but doesn’t automatically close?
If your RAMSET gate opener automatically opens, but doesn’t automatically close, the motor direction might be wrong. Turn on dip switch “C” 7 (left/right).
Why RAMSET RAM 100 Gate Opener doesn't close automatically?
If your RAMSET Gate Opener doesn't close automatically, it could be due to these reasons: * Dip switches “A” 1-3 are all ‘Off’. Set dip switches “A” 1-3 for auto close. * A dip switch is not fully engaged. Turn off dip switches “A” 1-3, then turn the appropriate switches back ‘On’.
What to do if RAMSET RAM 100 Gate Opener moves a couple of feet and then reverses?
If your RAMSET Gate Opener moves a couple of feet and then reverses, it might be because the E.R.D. is too sensitive. For 1/2 hp motors, turn dip switch “A” 4 ‘On’. For 3/4 hp motors, turn dip switch “B” 8 ‘On’.
How to fix RAMSET Gate Opener radio/receiver with no range?
If your RAMSET Gate Opener radio/receiver has no range: * Ensure the antenna is in the proper position and not shorted to the chassis, as the signal might be blocked. * Consider changing to a long range receiver if the area is not suitable for the current receiver type.
What to do if my RAMSET RAM 100 doesn't close?
If your RAMSET Gate Opener isn't closing, consider the following possibilities: * No lights are ‘On’ (refer to related solutions). * The Exit, Rev Loop, or Radio L.E.D. is ‘On’ (refer to related solutions). * A 10 amp fuse might be blown; check and replace it. * The thermal/overload button on the motor might have popped; reset it.
Details installer duties for gate operator installation, including operator selection and considerations.
Specifies UL standards for gate operator installation, gate type, and safe placement to prevent entrapment.
Details UL standards for control placement, safety zones, and required warning signs on gate panels.
Covers UL standards for placing non-contact and contact sensors to prevent entrapment and ensure proper function.
Outlines general provisions for entrapment protection, requiring multiple independent means.
Defines different types of entrapment protection systems (A, B1, B2, D) used in gate operators.
Provides critical safety instructions for operating and maintaining gate entrances to prevent injury.
General| Brand | RAMSET |
|---|---|
| Model | RAM 100 |
| Category | Gate Opener |
| Language | English |
To Next Page
