R&S ZNA26 - Page 1376

Command reference
R&S
®
ZNA
1376User Manual 1178.6462.02 ─ 20
7.3.14.25 [SENSe:]SEGMent<Seg>...
The [SENSe:]SEGMent<Seg>... commands define all channel settings for a seg-
mented frequency sweep. A segmented sweep is activated via [SENSe<Ch>:
]SWEep:TYPE SEGMent.
The commands in this subsystem do not accept the step parameters UP and DOWN.
Numeric values can be entered directly or using the DEFault, MINimum, MAXimum
parameters.
[SENSe<Ch>:]SEGMent:COUNt?..................................................................................1376
[SENSe<Ch>:]SEGMent<Seg>[:STATe]......................................................................... 1377
[SENSe<Ch>:]SEGMent<Seg>:ADD..............................................................................1377
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]...................................................... 1378
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:CONTrol.........................................1378
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:SELect........................................... 1379
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:SELect:CONTrol..............................1379
[SENSe<Ch>:]SEGMent<Seg>:DEFine..........................................................................1380
[SENSe<Ch>:]SEGMent<Seg>:DEFine:SELect.............................................................. 1382
[SENSe<Ch>:]SEGMent<Seg>:DELete:ALL................................................................... 1382
[SENSe<Ch>:]SEGMent<Seg>:DELete[:DUMMy]........................................................... 1383
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:CENTer?.....................................................1383
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:SPAN?........................................................1383
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:STARt.........................................................1384
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:STOP......................................................... 1384
[SENSe<Ch>:]SEGMent<Seg>:INSert........................................................................... 1384
[SENSe<Ch>:]SEGMent<Seg>:INSert:SELect................................................................1386
[SENSe<Ch>:]SEGMent<Seg>:POWer[:LEVel]...............................................................1387
[SENSe<Ch>:]SEGMent<Seg>:PORT<PortId>:POWer[:LEVel].........................................1387
[SENSe<Ch>:]SEGMent<Seg>:PORT<PortId>[:STATe]................................................... 1387
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol....................................................... 1388
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol:ALL.................................................1389
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol:CONTrol..........................................1390
[SENSe<Ch>:]SEGMent<Seg>:POWer[:LEVel]:CONTrol................................................. 1390
[SENSe<Ch>:]SEGMent<Seg>:SWEep:DWELl...............................................................1391
[SENSe<Ch>:]SEGMent<Seg>:SWEep:DWELl:CONTrol.................................................1392
[SENSe<Ch>:]SEGMent<Seg>:SWEep:POINts.............................................................. 1392
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME.................................................................1393
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME:CONTrol................................................... 1394
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME:SUM?.......................................................1394
[SENSe<Ch>:]SEGMent:COUNt?
Returns the number of sweep segments in the channel including all segments that are
switched off ([SENSe<Ch>:]SEGMent<Seg>[:STATe] OFF).
Suffix:
<Ch>
.
Channel number
SCPI command reference