Rath SmartRescue 2500-205D - Programming Options; Factory Default

Page 8
Programming Options
Step 8: Programming Options for SmartRescue
Option 1: Factory Default
TheEmergencyPhoneswillcalldirectlyo󰀨siteandnotstopattheSmartRescue.Thatphone’sbuttonwilllightat
the SmartRescue during the call.
**Keep in Default Mode if site is not manned 24/7 to answer calls onsite.
SOLID LIGHT: C ALLING
BLINKING LIGHT: RECEIVED
0
2
5
3
1
46
7
89
*
#
/
=
0
2
5
3
1
46
7
89
*
#
/
=
0
2
5
3
1
46
7
89
*
#
/
=
0
2
5
3
1
46
7
89
*
#
/
=
0
2
5
3
1
46
7
89
*
#
/
=
2 Pair- Twisted
24-22AWG
2 Pair- Twisted
24-22AWG
2 Pair- Twisted
24-22AWG
2 Pair- Twisted
24-22AWG
2 Pair- Twisted
24-22AWG
2500-PWR24U
1 Pair
18AWG
Hot
To 120vac
Ground
Neutral
EMERGENCY PHONE
SMARTRESCUE PHONE - 5
SUB-MASTER 2
SUB-MASTER 1
PHONE 1
PHONE 2
PHONE 3
PHONE 4
PHONE 5
BATTERY:
GREEN: FULL CHARGE
YELLOW: MID-LEVEL CHARGE
RED: LOW CHARGE
BATTERY
AC POWER
800-451-1460
WWW.RATHCOMMUNICATIONS.COM
DISCONNECT CALL TO
RESCUE SERVICES
RESCUE SERVICES
OPERATION:
1. SOLID LIT LED (PHONE, SUB-MASTER
OR RESCUE SERVICES) INDICATES
CALL IN PROGRESS.
2. SLOW BLINKING LED INDICATES
CALL ON HOLD.
3. LIFT HANDSET.
4. PRESS YELLOW TALK/HOLD BUTTON TO CALL
IN TO A SPECIFIC SUB-MASTER. IF THE GREEN
LED IS LIT YOU WILL JOIN CONVERSATION.
5. PRESS BLACK TALK/HOLD BUTTON TO CALL IN
TO A SPECIFIC PHONE. IF THE GREEN LED IS
LIT YOU WILL JOIN CONVERSATION.
6. PRESS TALK/HOLD BUTTON AGAIN TO PLACE
CONVERSATION ON HOLD.
7. PRESS RED DISCONNECT CALL TO RESCUE
SERVICES BUTTON TO END EXTERNAL CALL.
ANY PHONE AND SUB-MASTER ORIGINALLY
TALKING REMAIN IN CONVERSATION WITH
THIS UNIT.
8. HANG UP HANDSET TO END CALLS TO PHONE
AND SUB-MASTER.
READ ALL OPERATING STEPS
BEFORE PROCEEDING
SOLID LIGHT: C ALLING
BLINKING LIGHT: RECEIVED
EMERGENCY PHONE
SOLID LIGHT: C ALLING
BLINKING LIGHT: RECEIVED
EMERGENCY PHONE
SOLID LIGHT: C ALLING
BLINKING LIGHT: RECEIVED
EMERGENCY PHONE
SOLID LIGHT: C ALLING
BLINKING LIGHT: RECEIVED
EMERGENCY PHONE
Typical Wiring Diagram for Area of Refuge Applications
1 Pair
18 AWG
• Use 1 pair, 18 AWG wire for power (maximum distance is 5,100’)
• Do NOT wire more than 3 devices per wire run and a maximum
of 11 devices per Power Supply
• Incoming power on phones is not polarity sensitive
Note: For more information on the 2500-PWR24U, see the
RP8500225B Power Supply Manual.
Programming SmartRescue Back to Default Settings
1. Leave SmartRescue handset hung up.
2. Hold down red Disconnect and Sub-Master 1 buttons for 5 seconds
3. Releasebuttons(youwillhearaconrmationtone)
4. Press Phone 2 button, then red button, then Sub-Master 2 button, and then the Phone 5 button
5. PressSub-Master2button,thenSub-Master1button(youwillhearaconrmationtone)
0
2
5
3
1
4 6
7
8 9
*
#
0
2
5
3
1
4 6
7
8 9
*
#
0
2
5
3
1
4 6
7
8 9
*
#
0
2
5
3
1
4 6
7
8 9
*
#
0
2
5
3
1
4 6
7
8 9
*
#
2 Pair- Twisted
24-22ga
2 Pair- Twisted
24-22ga
2 Pair- Twisted
24-22ga
2 Pair- Twisted
24-22ga
2 Pair- Twisted
24-22ga
1 Pair Wire
From Telco
Plug-In
Transformer
GROUND
120vac HOT
NEUTRAL
GROUND
120vac HOT
NEUTRAL
GROUND
120vac HOT
NEUTRAL
GROUND
120vac HOT
NEUTRAL
GROUND
120vac HOT
NEUTRAL
SUB-MASTER 1
SUB-MASTER 2
OPERATION:
1. SOLID LIT LED (PHONE, SUB-MASTER
OR RESCUE SERVICES) INDICATES
CALL IN PROGRESS.
2. SLOW BLINKING LED INDICATES
CALL ON HOLD.
3. LIFT HANDSET.
4. PRESS YELLOW TALK/HOLD BUTTON TO CALL
IN TO A SPECIFIC SUB-MASTER. IF THE GREEN
LED IS LIT YOU WILL JOIN CONVERSATION.
5. PRESS BLACK TALK/HOLD BUTTON TO CALL IN
TO A SPECIFIC PHONE. IF THE GREEN LED IS
LIT YOU WILL JOIN CONVERSATION.
6. PRESS TALK/HOLD BUTTON AGAIN TO PLACE
CONVERSATION ON HOLD.
7. PRESS RED DISCONNECT CALL TO RESCUE
SERVICES BUTTON TO END EXTERNAL CALL.
ANY PHONE AND SUB-MASTER ORIGINALLY
TALKING REMAIN IN CONVERSATION WITH
THIS UNIT.
8. HANG UP HANDSET TO END CALLS TO PHONE
AND SUB-MASTER.
BATTERY
POWER
PHONE 1
PHONE 2
PHONE 3
PHONE 4
PHONE 5
DISCONNECT
CALL TO
RESCUE
SERVICES
SMARTRESCUE PHONE - 5
READ ALL OPERATING STEPS
BEFORE PROCEEDING
RESCUE SERVICES
SOLID LIGHT: CALLING
BLINKING LIGHT: RECEIVED
EMERGENCY PHONE
SOLID LIGHT: CALLING
BLINKING LIGHT: RECEIVED
EMERGENCY PHONE
SOLID LIGHT: CALLING
BLINKING LIGHT: RECEIVED
EMERGENCY PHONE
SOLID LIGHT: CALLING
BLINKING LIGHT: RECEIVED
EMERGENCY PHONE
SOLID LIGHT: CALLING
BLINKING LIGHT: RECEIVED
EMERGENCY PHONE
24/5VA
24/5VA
24/5VA
24/5VA
24/5VA
Wiring Diagram with Individual Transformers
N56W24720 N. Corporate Circle • Sussex, WI 53089
800-451-1460 • www.rathcommunications.com
12/21
Twisted, Shielded
Wire Recommended