red lion PAXCK - Parameter Value Chart

26
5-OPEr Timer Operating Modes
DISPLAY PARAMETER USER SETTING
FACTORY
SETTING
USEr-1
USER INPUT 1
NO
USEr-2
USER INPUT 2
NO
USEr-3
USER INPUT 3
NO
F1
FUNCTION KEY 1
NO
F2
FUNCTION KEY 2
NO
rSt
RESET KEY
drSt-E
SEC-F1 NO
SEC-F2
SECONDARY FUNCTION KEY F2
NO
1-INP Timer Input Parameters
2-FNC User Input and Function Key Parameters
3-LOC Display and Program Lock-out Parameters
4-CNt Cycle Counter Parameters
DISPLAY PARAMETER USER SETTING
FACTORY
SETTING
Sp0f-2
t-dSP
tOUt-2
C-dSP
SP2 OFF VALUE ACCESS
TIMER DISPLAY LOCK-OUT
LOC
rEd
LOC
LOC
sp-3
rtC-d
LOC
LOC
t Strt
sp-4
SP0F-1
sp0f-3
rtC-t
TIMER START VALUE ACCESS
SP4 ON VALUE ACCESS
SP1 OFF VALUE ACCESS
SP3 OFF VALUE ACCESS
RTC TIME DISPLAY LOCK-OUT
LOC
LOC
LOC
LOC
LOC
C StOP
t StOP
sp0f-4
tOUt-1
tOUt-3
Sp-1
COUNTER STOP VALUE ACCESS
TIMER STOP ACCESS
SP4 OFF VALUE ACCESS
SP1 TIME-OUT VALUE ACCESS
SP3 TIME-OUT VALUE ACCESS
SP1 ON VALUE ACCESS
LOC
LOC
LOC
LOC
LOC
LOC
COdE
SEt-t
C Strt
tOUt-4
Sp-2
SECURITY CODE
RTC TIME SETTING ACCESS
COUNTER START VALUE ACCESS
SP4 TIME-OUT VALUE ACCESS
SP2 ON VALUE ACCESS
000
LOC
LOC
LOC
LOC
C Src
NONE
VALUE
C dir
CYCLE COUNTER STOP VALUE (A)
000000
UP
C Strt
CYCLE COUNTER STOP VALUE (B)*
CYCLE COUNTER START VALUE (A)
OOOOOO
000000
C StOP
C p-UP
CYCLE COUNTER STOP (A & B*)
CYC. CNTR. RESET AT POWER-UP
CYCLE COUNTER START VALUE (B)*
NO
NO
000000
DISPLAY PARAMETER USER SETTING
FACTORY
SETTING
PARAMETER VALUE CHART
Programmer ________________ Date ________
PAXCK Clock Timer Meter# _____________ Security Code __________
SP2 TIME-OUT VALUE ACCESS
SP3 ON VALUE ACCESS
RTC DATE DISPLAY LOCK-OUT
DISPLAY PARAMETER
FACTORY
SETTING
USER SETTING
rANGE
TIMER RANGE
SSSSSS
FILtEr
INP OP
TIMER INPUT FILTERING
TIMER INPUT OPERATION

LEVEL
t dir
TIMING DIRECTION

t Strt
TIMER START VALUE (A)

TIMER START VALUE (B)*

t StOP
TIMER STOP (A & B*)
NO
VaLUE
TIMER STOP VALUE (A)

TIMER STOP VALUE (B)*

FLASH
FLASH TIMER ANNUNCIATOR

InP-UP
TIMER INPUT STATE AT POWER-UP

t p-UP
TIMER RESET AT POWER-UP

* See Module 2, Exchanging Parameter Lists, for details on programming this value.
SECONDARY FUNCTION KEY F1
CYCLE COUNTER COUNT SOURCE
CYC. CNTR. COUNTING DIRECTION
CYCLE COUNT DISPLAY LOCK-OUT

SETPOINT 1 TIME-OUT VALUE
tOUt-1
000100
SETPOINT 1 OFF VALUE
SPOF-1

SETPOINT 1 ON VALUE
SP-1
NO
PREDEFINED TIMER OPER. MODE
t OPEr
USER SETTING
FACTORY
SETTING
PARAMETERDISPLAY
Shaded areas are model dependent.Shaded areas are model dependent.