To Next PageTo Next PageWhat to do if the red lion Measuring Instruments display is jittery?
If the display is jittery, increase Module 1 filtering, rounding, and input range. Also, verify that the wiring follows EMC installation guidelines.
What to do if the red lion Measuring Instruments shows incorrect input display value?
If the input display value is incorrect, check the following: * Module 1 programming * Input Range Jumper position * Input connections * Input signal level * Module 4 Display Offset is zero Press DSP for Input Display. If the problem persists, perform Module 9 Calibration.
What does OLOL mean on my red lion Measuring Instruments display?
If “OLOL” is displayed (SIGNAL HIGH), check Module 1 programming, the Input Range Jumper position, input connections, and the input signal level.
What does ULUL mean on my red lion Measuring Instruments display?
If “ULUL” is displayed (SIGNAL LOW), check Module 1 programming, the Input Range Jumper position, input connections, and the input signal level.
How to fix a program locked-out on red lion Measuring Instruments?
If the program is locked-out, check the active (lock-out) user input and enter the security code when requested.
What to do if modules or parameters are not accessible on red lion Measuring Instruments?
If modules or parameters are not accessible, check the corresponding plug-in card installation.
What does error code Err 1-4 mean on red lion Measuring Instruments?
If you see error code Err 1-4, press the Reset KEY. If that doesn't clear the error, contact factory.
How to fix max, min, tot locked-out on red lion Measuring Instruments?
If MAX, MIN, or TOT is locked-out, check Module 3 programming.
How to disable zero chop feature on red lion Measuring Instruments?
To disable the zero chop feature, program Module 4 as Hi-t: 0.0 LO-t: 3271.1.
How to troubleshoot no display on a red lion Measuring Instruments?
To troubleshoot a 'no display' issue, check the power level and power connections.
General| Brand | red lion |
|---|---|
| Model | PAXD Series |
| Category | Measuring Instruments |
| Language | English |
Details power requirements for AC and DC versions of the meter.
Explains how to select the proper input range using the jumper.
Offers guidelines for ensuring electromagnetic compatibility during installation.
Shows wiring diagrams for various PAXD input signal types.
Illustrates wiring diagrams for various PAXP input signal types.
Explains the two programming modes: Full and Quick.
Describes how to enter the programming mode.
Details input range selections for PAXD.
Lists available input types for PAXT, including RTD and custom options.
Details input range selections for PAXS.
Details input range selections for PAXH.
Allows zeroing the input display value for applications like weighing.
Switches the input display between relative and absolute values.
Locks programming mode, allowing access only with a security code.
Resets the maximum reading to the current input display value.
Manages the maximum value display and detection.
Selects the minimum display value, holding it until released.
Resets the minimum reading to the current input display value.
Manages the minimum value display and detection.
Resets both maximum and minimum readings simultaneously.
Locks out the maximum display from view.
Locks out the minimum display from view.
Locks out the totalizer display from view.
Controls access to setpoint displays for modification.
Sets a security code to protect programming mode access.
Enables automatic compensation for zero drift.
Selects which setpoint to configure.
Resets all user settings to factory defaults.
General information regarding meter calibration.
Step-by-step guide for calibrating PAXP input ranges.
Step-by-step guide for calibrating PAXD input ranges.
Step-by-step guide for calibrating PAXH input ranges using DC signals.
Guide to calibrating PAXS input ranges, including signal connection.
Provides calibration steps for PAXT input types.
Details calibration procedure for 10 ohm RTD ranges.
Details calibration procedure for 100 ohm RTD ranges.
Step-by-step guide for calibrating thermocouple ranges.
Procedure for calibrating the ice point compensation.
Steps to calibrate the analog output card.
Troubleshoots issues related to the display not turning on.
Provides steps to resolve programming lock-out issues.
Addresses problems with inaccurate input display readings.
Troubleshoots display showing "OLOL" indicating a high signal.
Troubleshoots display showing "ULUL" indicating a low signal.
Explains how to handle error codes displayed by the meter.
Setting to lock the maximum display.
Setting to lock the minimum display.
Setting to lock the totalizer display.
Parameter for setting the programming mode security code.
Sets the delay for PAXS auto-zero tracking.
Sets the band for PAXS auto-zero tracking.
Selects which setpoint to configure.
Defines setpoint action (e.g., output logic, reset).
Sets the numerical value for setpoint alarms.
Essential safety regulations and warnings for the LPAX Display.
Detailed steps for installing the MPAX module into the LPAX case.
