REMEHA Quinta Pro 115 Installation And Service Manual

REMEHA Quinta Pro 115

96 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Great Britain

EN

Wall-hung gas condensing boilers

Quinta Pro 30 - 45 - 65 - 90 - 115

Installation and

Service Manual

123157-AA

Table of Contents

Other manuals for REMEHA Quinta Pro 115

Installation, User And Service Manual88 pages

Questions and Answers:

S
Stephanie BowenAug 28, 2025
What causes REMEHA Quinta Pro 115 Boiler temperature of heat exchanger to be too low?
- B
  blakejasonAug 28, 2025
  If the temperature of the heat exchanger in your REMEHA boiler is too low, it could be due to a bad connection, the sensor not being connected correctly, or no circulation. Check that the sensors are operating correctly, and that the sensor has been fitted properly. If necessary, replace the sensor. Vent the air from the CH system, check the circulation (direction, pump, valves), the water pressure, and the cleanliness of the heat exchanger. If present, check the boiler type parameter setting.
R
Rachel FisherAug 28, 2025
What to do if REMEHA Quinta Pro 115 Boiler shows communication error with the SCU PCB?
- M
  melissa06Aug 28, 2025
  If your REMEHA boiler shows a communication error with the SCU PCB, it may be due to a poor connection with the BUS or the SCU PCB not being present in the boiler. Check the wiring and carry out automatic detection.
D
Douglas DoyleAug 29, 2025
What causes REMEHA Quinta Pro 115 fan operation error?
- E
  ecookAug 29, 2025
  A fan operation error in your REMEHA boiler could stem from a bad connection or a defective fan. Ensure adequate draw on the chimney connection and replace the fan if necessary.
Z
zhillAug 29, 2025
Why does REMEHA Quinta Pro 115 Boiler have maximum difference between the flow and return temperature exceeded?
- D
  Diane MooreAug 29, 2025
  If the maximum difference between the flow and return temperature is exceeded in your REMEHA boiler, it could be due to no flow or insufficient flow, or a sensor error. Check the flow (direction, pump, valves), the water pressure, that the sensors are operating correctly, that the sensor has been fitted properly, and the cleanliness of the heat exchanger.
B
Brandi StewartAug 30, 2025
What to do if REMEHA Quinta Pro 115 phase and neutral of mains supply mixed up?
- T
  Tony TurnerAug 30, 2025
  If the phase and neutral of the mains supply are mixed up in your REMEHA boiler, it is likely due to incorrectly wired mains supply or a floating network or 2-phase network. Invert phase and neutral and set parameter to the correct setting.
J
Jason SchwartzAug 30, 2025
Why REMEHA Quinta Pro 115 Boiler has no release signal?
- J
  James CookAug 31, 2025
  If your REMEHA boiler has no release signal, it could be due to an external cause, parameter error, or bad connection. Remove any external causes, check the parameters, and check the wiring.
Q
qjamesAug 31, 2025
What to do if the REMEHA Quinta Pro 115 flow temperature sensor is short circuited?
- S
  Stephen HardinAug 31, 2025
  If the flow temperature sensor of your REMEHA Boiler is short circuited, it could be due to several reasons. First, check the wiring for any bad connections. Then, verify that the sensors are operating correctly and that the sensor has been correctly fitted. If these steps don't resolve the issue, consider replacing the sensor.
S
Shawn ShepherdAug 31, 2025
What to do if the REMEHA Quinta Pro 115 safety parameters are incorrect?
- J
  Jeffrey RobertsSep 1, 2025
  If the safety parameters for your REMEHA Boiler are incorrect, it might be due to a bad connection. In this case, check the wiring. Alternatively, the PSU could be defective, so consider replacing it.
D
Danielle CarrollSep 1, 2025
What to do if the REMEHA Boiler flow temperature sensor has an open circuit?
- A
  Ashlee CookSep 1, 2025
  If the flow temperature sensor of your REMEHA Boiler has an open circuit, first check the wiring for any bad connections. Also, check that the sensors are operating correctly and that the sensor has been correctly fitted. If the problem persists, replace the sensor.
B
Billy SingletonSep 1, 2025
How to fix REMEHA Quinta Pro 115 storage unit PSU parameter not found?
- H
  Holly HartSep 2, 2025
  If the storage unit PSU parameter is not found in your REMEHA Boiler, the problem could be a bad connection. Check the wiring to resolve this issue.

REMEHA Quinta Pro 115 Specifications

General

Model	Quinta Pro 115
Type	Condensing Boiler
Output	115 kW
Max. Heat Output	115 kW
Fuel Type	Natural gas, LPG
Fuel	Natural Gas or Propane

Related product manuals

REMEHA Quinta Ace 115

Preview: REMEHA Quinta 115

REMEHA Quinta 115

Preview: REMEHA Quinta Ace 135

REMEHA Quinta Ace 135

Preview: REMEHA Quinta 45

REMEHA Quinta 45

REMEHA Quinta 30

Preview: REMEHA Quinta Ace

REMEHA Quinta Ace

Preview: REMEHA Quinta Pro

REMEHA Quinta Pro

Preview: REMEHA Quinta Pro 30

REMEHA Quinta Pro 30

Preview: REMEHA Quinta Ace 30

REMEHA Quinta Ace 30

REMEHA Quinta Pro 90

REMEHA Quinta Pro 45

REMEHA Quinta Pro 65