REMEHA Quinta Pro 30 - User Manual

Other manuals for REMEHA Quinta Pro 30

Installation And Service Manual96 pages

Manual32 pages

Questions and Answers

J
Joshua AustinSep 9, 2025
Why maximum difference between flow and return temperature exceeded in REMEHA Boiler?
- T
  Thomas PenningtonSep 9, 2025
  If the maximum difference between the flow and return temperature has been exceeded on your REMEHA Boiler, check the circulation (direction, pump, valves) because the cause may be non-existent or insufficient circulation. Also, check the water pressure, check that the sensors are operating correctly, check that the sensor has been correctly fitted and check the cleanliness of the heating body.
C
Curtis RichardsonAug 25, 2025
What to do if the REMEHA Quinta Pro 30 flow temperature sensor is short circuited?
- P
  Paul VargasAug 25, 2025
  If the flow temperature sensor of your REMEHA Boiler is short circuited, it could be due to several reasons. First, check the wiring for any bad connections. Then, verify that the sensors are operating correctly and that the sensor has been correctly fitted. If these steps don't resolve the issue, consider replacing the sensor.
K
Keith GravesAug 25, 2025
What to do if the REMEHA Boiler safety parameters are incorrect?
- M
  Michael RyanAug 26, 2025
  If the safety parameters for your REMEHA Boiler are incorrect, it might be due to a bad connection. In this case, check the wiring. Alternatively, the PSU could be defective, so consider replacing it.
S
Sharon ArellanoSep 23, 2025
What causes storage unit PSU parameter not found in REMEHA Quinta Pro 30?
- M
  Mr. Matthew JonesSep 23, 2025
  If the storage unit PSU parameter is not found on your REMEHA Boiler, check the wiring for bad connection.
J
James ChapmanSep 10, 2025
How to fix flow and return reversed in REMEHA Boiler?
- L
  leah66Sep 10, 2025
  If the flow and return are reversed in your REMEHA Boiler, check the wiring for bad connections. Replace the sensor if necessary. Also, check that the sensors are operating correctly and check the circulation (direction, pump, valves) because the water circulation direction may be reversed. Check that the sensor has been correctly fitted.
T
timothywhiteSep 14, 2025
How to troubleshoot gas valve SU PCB problem in REMEHA Quinta Pro 30 Boiler?
- K
  Karl SanfordSep 14, 2025
  If there is a problem on the gas valve SU PCB of your REMEHA Boiler, check the wiring for bad connections. If the SU PCB is defective, inspect it and replace it if need be.
N
nicholas27Sep 4, 2025
What does it mean if the parameter storage unit PSU is not found in my REMEHA Quinta Pro 30?
- J
  Joseph FisherSep 4, 2025
  If the parameter storage unit PSU is not found in your REMEHA Boiler, it could be due to a bad connection. Check the wiring.
J
james34Sep 4, 2025
What to do if REMEHA Quinta Pro 30 burner start-up fails but there is ignition arc?
- M
  Michael MunozSep 5, 2025
  If your REMEHA Boiler is experiencing burner start-up failures and there is presence of the ignition arc but no flame formation, one potential cause is the gas conduit may need to be degassed. Also, check that the gas valve is correctly opened, the supply pressure is adequate, the gas valve unit is operating and set correctly, the air inlet and flue gas discharge flues are not blocked, and the wiring on the gas valve unit is intact. A defective control SU PCB could also be the cause.
A
Anne MillerSep 23, 2025
How to fix internal error on SU PCB in REMEHA Boiler?
- C
  Carrie RichardsonSep 23, 2025
  If your REMEHA Boiler has an internal error on the SU PCB, replace the SU PCB.
C
christine89Aug 29, 2025
What causes the gas pressure to be too low in my REMEHA Quinta Pro 30 Boiler?
- D
  Daniel ReedAug 30, 2025
  If the gas pressure is too low in your REMEHA Boiler, check that the gas valve is fully opened and check the gas supply pressure. Also, check whether the GPS has been correctly fitted and replace the GPS switch if necessary.