How do I troubleshoot a short-circuited return temperature sensor in my REMEHA Boiler?
If the return temperature sensor is short-circuited in your REMEHA Boiler, check the wiring. Also, check that the sensors are operating correctly and replace the sensor if necessary.
How to fix REMEHA Quinta Pro 45 Boiler maximum flow temperature exceeded?
If the maximum flow temperature is exceeded in your REMEHA boiler, it could be due to no flow or insufficient flow. Check the flow (direction, pump, valves) and reasons for the heat demand.
What to do if the water pressure is too low in my REMEHA Quinta Pro 45 Boiler?
If the water pressure is too low in your REMEHA Boiler, you should check the water pressure. Also, fill the boiler and the installation with water.
How to fix return temperature sensor short circuit in REMEHA Quinta Pro 45?
If the return temperature sensor is short circuited in your REMEHA Boiler, check the wiring for bad connections. Also, check that the sensors are operating correctly and that the sensor has been correctly fitted.
What causes a fan operation error in a REMEHA Boiler?
If there is a fan operation error in your REMEHA Boiler, check the wiring. Also, if the fan is defective, check for adequate draw on the chimney connection and replace the fan if necessary.
Why REMEHA Quinta Pro 45 Boiler heat exchanger temperature is too high?
If the temperature of heat exchanger is too high in your REMEHA Boiler, check the wiring for bad connections. Also, check that the sensors are operating correctly and that the sensor has been correctly fitted. If there is no circulation, check the circulation (direction, pump, valves). You may also need to check the water pressure and the cleanliness of the heating body.
How to fix REMEHA Quinta Pro 45 Boiler storage unit PSU parameter not found?
If the storage unit PSU parameter is not found in your REMEHA Boiler, the problem could be a bad connection. Check the wiring to resolve this issue.
What to do if there is no flame during operation in my REMEHA Quinta Pro 45?
If there's no flame during operation of your REMEHA Boiler, here's what you can check: * Vent the gas supply to remove any air. * Ensure the gas valve is fully opened and verify the gas supply pressure. * Check the operation and setting of the gas valve unit. * Make sure the air supply inlet and flue gas outlet are not blocked. * Ensure there is no recirculation of flue gases.
What to do if REMEHA Boiler shows communication error with the SCU PCB?
If your REMEHA boiler shows a communication error with the SCU PCB, it may be due to a poor connection with the BUS or the SCU PCB not being present in the boiler. Check the wiring and carry out automatic detection.
What causes REMEHA Boiler fan operation error?
A fan operation error in your REMEHA boiler could stem from a bad connection or a defective fan. Ensure adequate draw on the chimney connection and replace the fan if necessary.
Key safety guidelines for installers and end-users regarding gas and flue gas hazards.
Guidance on appliance usage, maintenance, and safe operation practices.
Outlines responsibilities of manufacturer, installer, and user regarding the appliance.
Explains danger levels and symbols used throughout the manual for clarity and safety.
Lists and defines abbreviations used in the manual for technical terms.
Details certifications, NOx class, and connection types for the boiler.
Presents comprehensive technical data including output, efficiency, gas, and electrical specifications.
Provides diagrams showing physical dimensions and connection points of the boiler.
Illustrates the boiler's electrical layout and component connections.
Highlights key features like high efficiency, low emissions, and suitability for cascade systems.
Explains how the boiler functions, including pump operation, water flow, and cascade systems.
Identifies and labels the key physical components of the boiler.
Details the functions of the control panel keys and display symbols.
Lists items included in the standard package with the boiler.
Mentions the availability of various optional accessories for the boiler.
Specifies requirements for installers, including registration and qualifications.
Guidelines for selecting an appropriate installation site considering safety and accessibility.
Explains the information found on the boiler's type plate, including serial number and specifications.
Provides guidance on determining the correct installation space and ensuring accessibility.
Specifies compliance requirements for ventilation standards.
General warning that installation must be done by a qualified installer.
Steps for preparing the boiler for mounting, including using the template.
Detailed instructions for mounting the boiler on the wall using the provided bracket.
Procedures for connecting the boiler to the heating system's water circuits.
Emphasizes the importance of cleaning and flushing the heating system before connecting the boiler.
Step-by-step guide for connecting the flow and return pipes of the heating circuit.
Instructions for correctly installing the expansion vessel into the heating system.
Details on connecting the condensate drain pipe, including safety precautions for the siphon.
Procedures and safety warnings for connecting the boiler to the gas supply.
Information on different types of flue gas connections and their classifications.
Details classifications for flue gas connections according to CE standards.
Lists manufacturers for drain systems and notes on flue gas outlet materials.
Specifies material requirements for flue gas and air supply pipework.
Provides tables for maximum chimney lengths based on diameter and type.
General advice for installing flue gas and air supply materials, including tightness checks.
Instructions for connecting flue gas and air supply pipes, including gradient and resting precautions.
Covers electrical connections for the control unit and power supply.
Specifies important connection values and safety warnings for the control unit.
Safety recommendations for making electrical connections, emphasizing qualified personnel.
Step-by-step guide to accessing and connecting various thermostats and regulators.
Details how to connect pumps, thermostats, and other accessories to the standard PCB.
Identifies PCBs installed in the housing and their functions.
General warning about not operating the boiler with incorrect gas types.
Instructions for checking gas inlet pressure and connections on the gas valve unit.
Checks for the siphon and water-side connections before commissioning.
Final check of all electrical connections prior to commissioning.
Steps for initial commissioning, including gas type adaptation and safety warnings.
Procedures for adapting to different gas types and setting the gas/air ratio.
Instructions for qualified engineers to adapt the boiler for different gas types.
Detailed steps for measuring and adjusting O2/CO2 levels for optimal combustion.
Lists and describes adjustable parameters, their ranges, and factory settings.
Guides on how to modify user-level and installer-level parameters.
Step-by-step instructions for users to adjust specific parameters.
Instructions for installers to modify advanced parameters using a special access code.
Information on setting the maximum heat output for central heating operation.
Procedure to reset all parameters to their original factory defaults.
Steps to perform an auto-detect after removing or replacing a PCB.
How to manually set the boiler's operating mode when a controller is not connected.
Instructions on how to read current operating values and status information from the control panel.
Lists and explains how to display various real-time sensor and operating data.
How to access and view the boiler's operating hours and start success rate.
Explains the meaning of different status and sub-status codes shown on the display.
General advice on the low maintenance requirements of the boiler and the need for periodic inspection.
Explains the automatic service message system and its purpose for preventive maintenance.
Procedure for resetting service messages after maintenance is completed.
How to initiate the next service interval after maintenance has been performed.
Lists routine checks and maintenance tasks to ensure proper operation.
How to check and maintain the correct water pressure in the heating system.
Procedure for checking the ionisation current and when to replace the electrode.
Inspecting flue gas and air supply connections for condition and tightness.
Method for checking combustion by measuring O2/CO2 in flue gases.
Steps to check the automatic air vent for water visibility and leaks.
Instructions for dismantling, cleaning, and refitting the siphon, emphasizing its function.
Detailed steps for accessing, cleaning, and inspecting the burner and heat exchanger.
Procedures for specific maintenance tasks that may be required.
Step-by-step guide for replacing the ionisation/ignition electrode.
Instructions for inspecting and replacing the non-return valve.
Steps for correctly reassembling the boiler after maintenance or component replacement.
Explains that the boiler displays error codes for faults and how to interpret them.
Describes the temporary blocking mode, its causes, and how to read blocking codes.
Explains that the boiler stores the last 16 errors and associated data.
Procedure to access and view stored error codes and related operational data.
Steps to clear stored error codes from the boiler's memory.
Instructions for safe and compliant removal and disposal of the boiler.
Guidance on using only original or recommended parts for replacements.
Exploded diagrams and part numbers for identifying components for maintenance or repair.
Provides product data and energy efficiency information as per ErP regulations.
Summarizes key performance data and energy efficiency ratings for each model.
Details energy efficiency calculations for boiler and heat pump packages.
States the unit's compliance with standard types and European directives.
Details connection options for various optional PCBs for extended functionality.
Instructions for accessing and installing additional PCBs into the boiler's housing.
Details connections for minimum gas pressure switch and heat recovery unit.
Explains connections for 230 VAC or 24 VAC three-way valves.
Details control options for modulating central heating pumps via various signals.
Describes PCB's ability to control heating groups or calorifiers and cascade systems.
To Next Page
General