REMEHA Quinta Pro 30 Manual

REMEHA Quinta Pro 30

32 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

PANTONE 287 EC

PANTONE 287 EC

PANTONE

Process Black EC

PANTONE 200 EC PANTONE 376 EC PANTONE

Process Cyan EC

PANTONE

Process Cyan EC

SUPER CONDENSING

107% NCV ≥ 82/71°C

FULLY MODULATING

BOILER CONTROL

PREMIX BURNER

CLEAN COMBUSTION

ULTRA LOW NOx

BREEAM EXCELLENT

RECYCLABLE

MATERIALS

PANTONE 2985 EC

PANTONE 2985 EC

HIGH EFFICIENCY

108.9% NCV ∆T 50/30°C

REMEHA QUINTA PRO RANGE - SUGGESTED SCHEMATICS WITH CONTROL AND POWER WIRING DETAILS

QUINTA PRO RANGE

Suggested Schematics with Control

and Power Wiring Details

QUINTA PRO RANGE OUTPUTS

QP30: 8.0 - 31.4 kW

QP45: 8.0 - 43.0 kW

QP65: 12.0 - 65.0 kW

QP90: 14.1 - 89.5 kW

QP115: 16.6 - 114.0 kW

High efﬁciency wall hung condensing boiler

with ultra low NOx emissions

Other manuals for REMEHA Quinta Pro 30

Installation, User And Service Manual88 pages

Installation And Service Manual96 pages

Questions and Answers:

J
Joshua AustinSep 9, 2025
Why maximum difference between flow and return temperature exceeded in REMEHA Boiler?
- T
  Thomas PenningtonSep 9, 2025
  If the maximum difference between the flow and return temperature has been exceeded on your REMEHA Boiler, check the circulation (direction, pump, valves) because the cause may be non-existent or insufficient circulation. Also, check the water pressure, check that the sensors are operating correctly, check that the sensor has been correctly fitted and check the cleanliness of the heating body.
C
Curtis RichardsonAug 25, 2025
What to do if the REMEHA Quinta Pro 30 flow temperature sensor is short circuited?
- P
  Paul VargasAug 25, 2025
  If the flow temperature sensor of your REMEHA Boiler is short circuited, it could be due to several reasons. First, check the wiring for any bad connections. Then, verify that the sensors are operating correctly and that the sensor has been correctly fitted. If these steps don't resolve the issue, consider replacing the sensor.
K
Keith GravesAug 25, 2025
What to do if the REMEHA Boiler safety parameters are incorrect?
- M
  Michael RyanAug 26, 2025
  If the safety parameters for your REMEHA Boiler are incorrect, it might be due to a bad connection. In this case, check the wiring. Alternatively, the PSU could be defective, so consider replacing it.
J
Jose PalmerAug 26, 2025
What to do if the REMEHA Quinta Pro 30 flow temperature sensor has an open circuit?
- G
  greenryanAug 26, 2025
  If the flow temperature sensor of your REMEHA Boiler has an open circuit, first check the wiring for any bad connections. Also, check that the sensors are operating correctly and that the sensor has been correctly fitted. If the problem persists, replace the sensor.
J
James ChapmanSep 10, 2025
How to fix flow and return reversed in REMEHA Boiler?
- L
  leah66Sep 10, 2025
  If the flow and return are reversed in your REMEHA Boiler, check the wiring for bad connections. Replace the sensor if necessary. Also, check that the sensors are operating correctly and check the circulation (direction, pump, valves) because the water circulation direction may be reversed. Check that the sensor has been correctly fitted.
T
timothywhiteSep 14, 2025
How to troubleshoot gas valve SU PCB problem in REMEHA Quinta Pro 30 Boiler?
- K
  Karl SanfordSep 14, 2025
  If there is a problem on the gas valve SU PCB of your REMEHA Boiler, check the wiring for bad connections. If the SU PCB is defective, inspect it and replace it if need be.
N
nicholas27Sep 4, 2025
What does it mean if the parameter storage unit PSU is not found in my REMEHA Quinta Pro 30?
- J
  Joseph FisherSep 4, 2025
  If the parameter storage unit PSU is not found in your REMEHA Boiler, it could be due to a bad connection. Check the wiring.
J
james34Sep 4, 2025
What to do if REMEHA Quinta Pro 30 burner start-up fails but there is ignition arc?
- M
  Michael MunozSep 5, 2025
  If your REMEHA Boiler is experiencing burner start-up failures and there is presence of the ignition arc but no flame formation, one potential cause is the gas conduit may need to be degassed. Also, check that the gas valve is correctly opened, the supply pressure is adequate, the gas valve unit is operating and set correctly, the air inlet and flue gas discharge flues are not blocked, and the wiring on the gas valve unit is intact. A defective control SU PCB could also be the cause.
J
Jessica WangAug 31, 2025
What to do if the temperature of the heat exchanger is too low in my REMEHA Quinta Pro 30?
- J
  Jeanette SwansonAug 31, 2025
  If the temperature of the heat exchanger is too low in your REMEHA Boiler, check the wiring and ensure the sensors are operating correctly and that the sensor has been fitted properly. Replace the sensor if necessary. Also, vent the air from the CH system, check the circulation (direction, pump, valves), check the water pressure and the cleanliness of the heat exchanger. If present, check the boiler type parameter setting.
C
christine89Aug 29, 2025
What causes the gas pressure to be too low in my REMEHA Quinta Pro 30 Boiler?
- D
  Daniel ReedAug 30, 2025
  If the gas pressure is too low in your REMEHA Boiler, check that the gas valve is fully opened and check the gas supply pressure. Also, check whether the GPS has been correctly fitted and replace the GPS switch if necessary.

REMEHA Quinta Pro 30 Specifications

General

Model	Quinta Pro 30
Category	Boiler
Type	Condensing Boiler
Output	30 kW
Fuel	Gas
Warranty	2 years
Fuel Type	Natural Gas
Efficiency	98% (GCV)

Related product manuals

Preview: REMEHA Quinta Ace 30

REMEHA Quinta Ace 30

REMEHA Quinta 30

Preview: REMEHA Quinta 45

REMEHA Quinta 45

Preview: REMEHA Quinta Ace

REMEHA Quinta Ace

Preview: REMEHA Quinta 115

REMEHA Quinta 115

Preview: REMEHA Quinta Pro

REMEHA Quinta Pro

REMEHA Quinta Pro 90

REMEHA Quinta Pro 45

REMEHA Quinta Pro 65

Preview: REMEHA Quinta Ace 135

REMEHA Quinta Ace 135

Preview: REMEHA Quinta Pro 115

REMEHA Quinta Pro 115

REMEHA Quinta Ace 115