REMEHA Quinta Pro 30 User Manual (English)

Other manuals for REMEHA Quinta Pro 30

Installation And Service Manual96 pages

Manual32 pages

Questions and Answers:

J
Jessica WangAug 31, 2025
What to do if the temperature of the heat exchanger is too low in my REMEHA Quinta Pro 30?
- J
  Jeanette SwansonAug 31, 2025
  If the temperature of the heat exchanger is too low in your REMEHA Boiler, check the wiring and ensure the sensors are operating correctly and that the sensor has been fitted properly. Replace the sensor if necessary. Also, vent the air from the CH system, check the circulation (direction, pump, valves), check the water pressure and the cleanliness of the heat exchanger. If present, check the boiler type parameter setting.
J
Joshua AustinSep 9, 2025
Why maximum difference between flow and return temperature exceeded in REMEHA Boiler?
- T
  Thomas PenningtonSep 9, 2025
  If the maximum difference between the flow and return temperature has been exceeded on your REMEHA Boiler, check the circulation (direction, pump, valves) because the cause may be non-existent or insufficient circulation. Also, check the water pressure, check that the sensors are operating correctly, check that the sensor has been correctly fitted and check the cleanliness of the heating body.
C
christine89Aug 29, 2025
What causes the gas pressure to be too low in my REMEHA Quinta Pro 30 Boiler?
- D
  Daniel ReedAug 30, 2025
  If the gas pressure is too low in your REMEHA Boiler, check that the gas valve is fully opened and check the gas supply pressure. Also, check whether the GPS has been correctly fitted and replace the GPS switch if necessary.
R
Ronnie SchneiderSep 12, 2025
How to fix return temperature sensor short circuit in REMEHA Quinta Pro 30 Boiler?
- K
  Karen BarnesSep 12, 2025
  If the return temperature sensor is short circuited in your REMEHA Boiler, check the wiring for bad connections. Also, check that the sensors are operating correctly and that the sensor has been correctly fitted.
M
Michael GomezSep 12, 2025
What causes flow temperature sensor short circuit in REMEHA Quinta Pro 30?
- H
  heatherriddleSep 12, 2025
  If the flow temperature sensor is short circuited in your REMEHA Boiler, check the wiring for bad connections. Also, check that the sensors are operating correctly and that the sensor has been correctly fitted. Replace the sensor if necessary.
T
timothywhiteSep 14, 2025
How to troubleshoot gas valve SU PCB problem in REMEHA Quinta Pro 30 Boiler?
- K
  Karl SanfordSep 14, 2025
  If there is a problem on the gas valve SU PCB of your REMEHA Boiler, check the wiring for bad connections. If the SU PCB is defective, inspect it and replace it if need be.
L
Laura WashingtonAug 27, 2025
What to do if there is no flame during operation in my REMEHA Quinta Pro 30?
- S
  Susan SchaeferAug 27, 2025
  If there's no flame during operation of your REMEHA Boiler, here's what you can check: * Vent the gas supply to remove any air. * Ensure the gas valve is fully opened and verify the gas supply pressure. * Check the operation and setting of the gas valve unit. * Make sure the air supply inlet and flue gas outlet are not blocked. * Ensure there is no recirculation of flue gases.
S
Scott SmithAug 27, 2025
How to fix REMEHA Quinta Pro 30 storage unit PSU parameter not found?
- S
  Scott StoneAug 27, 2025
  If the storage unit PSU parameter is not found in your REMEHA Boiler, the problem could be a bad connection. Check the wiring to resolve this issue.
J
Jose PalmerAug 26, 2025
What to do if the REMEHA Quinta Pro 30 flow temperature sensor has an open circuit?
- G
  greenryanAug 26, 2025
  If the flow temperature sensor of your REMEHA Boiler has an open circuit, first check the wiring for any bad connections. Also, check that the sensors are operating correctly and that the sensor has been correctly fitted. If the problem persists, replace the sensor.
K
Keith GravesAug 25, 2025
What to do if the REMEHA Boiler safety parameters are incorrect?
- M
  Michael RyanAug 26, 2025
  If the safety parameters for your REMEHA Boiler are incorrect, it might be due to a bad connection. In this case, check the wiring. Alternatively, the PSU could be defective, so consider replacing it.