What does Configuration Error mean in REMEHA Quinta Ace 115?
If your REMEHA Boiler is showing a Configuration Error, it may be due to a configuration error or an unknown configuration number. Reset CN1 and CN2.
What to do if the Return temperature difference is too large in REMEHA Boiler?
A large return temperature difference in your REMEHA Boiler can be caused by: * Air in the central heating system: Vent the system to remove air. * Water pressure issues: Check the water pressure. * Incorrect boiler type parameter setting: Verify the setting. * Circulation problems: Check the direction, pump, and valves. * Heating pump malfunction: Ensure the pump is operating correctly. * Heat exchanger cleanliness: Inspect and clean the heat exchanger if necessary. * Sensor issues: Check the operation and fitting of the sensors. Replace the sensor if necessary.
Why does my REMEHA Quinta Ace 115 show a 5x Error of unintended Flame Loss occurrence?
If your REMEHA Boiler shows a 5x Error of unintended Flame Loss occurrence, it could be due to: * Low ionization current: Vent the gas supply to remove air. * Gas valve issues: Ensure the gas valve is fully opened and check its operation and setting. * Gas supply problems: Check the gas supply pressure. * Blockages: Verify that the air supply inlet and flue gas outlet are not blocked. * Flue gas recirculation: Ensure there is no recirculation of flue gases.
What causes maximum heat exchanger temperature increase exceeded in REMEHA Boiler?
If the maximum heat exchanger temperature increase has been exceeded in your REMEHA Boiler, check the circulation (direction, pump, valves) and the water pressure. Also, check the cleanliness of the heat exchanger. Ensure that the sensors are operating correctly and that the sensor has been fitted properly.
Why water pressure sensor was expected but not detected in REMEHA Quinta Ace 115?
If the water pressure sensor was expected but not detected on your REMEHA Boiler, connect the sensor if the water pressure sensor is not connected or connect the sensor correctly if it is not connected correctly.
What to do if The time reserved for the shower has elapsed in REMEHA Boiler?
If the time reserved for the shower has elapsed on your REMEHA Boiler, take a shorter shower or adjust parameter DP357.
What does Communication Error occured mean in REMEHA Boiler?
If a Communication Error occurred in your REMEHA Boiler, it could be due to a communication error with the security kernel. In this case, restart the boiler. If the problem persists, replace the CU-GH.
What to do if gas valve control internal locking in REMEHA Boiler?
If there is a Gas Valve Control internal locking on your REMEHA Boiler, restart the boiler or replace the CU-GH.
What to do if return temperature sensor is either shorted or measures a temperature above range in REMEHA Quinta Ace 115 Boiler?
If the return temperature sensor is either shorted or measures a temperature above range on your REMEHA Boiler, check the wiring and connectors if the return temperature sensor is short-circuited. Also, check that the sensor has been correctly fitted if it was incorrectly fitted and replace the sensor if it's faulty.
Why is the return temperature sensor not detected in my REMEHA Quinta Ace 115 Boiler?
If the return temperature sensor was expected but not detected on your REMEHA Boiler, check the wiring and connectors. Also, consider replacing the sensor.
Safety guidelines for installers and end-users regarding gas and flue gas.
Guidelines for selecting installation location and adhering to regulations.
Specifies requirements for connecting water, gas, and flue gas systems.
Procedures for connecting gas, flue gas, and air supply components.
Steps for initial boiler commissioning, including gas settings and adjustments.
Explains different types of error codes, warnings, and their meanings.
General| Model | Quinta Ace 115 |
|---|---|
| Category | Boiler |
| Output | 115 kW |
| Fuel Type | Natural Gas |
| Installation Type | Wall-mounted |
To Next Page
