Renfert MT3 - User Manual

12 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

#FEJFOVOHTBOMFJUVOH

*OTUSVDUJPONBOVBM߭.PEFEtFNQMPJ

*TUSV[JPOJEߤVTP߭*OTUSVDDJPOFTQBSBFMTFSWJDJP



ᜪ◅一⥢⩌߭瞦綣砞煿砖߭佈⥢ᆺ

.BEFJO(FSNBOZ

MT3 / MT3 pro

Nr. 1808 / 1809

21-6616 23052012 A

Ideas for dental technology

Table of Contents

Questions and Answers

M
Mary HillAug 27, 2025
Why is the grinding table wobbling on my Renfert Laboratory Equipment?
- R
  Rebecca PattersonAug 27, 2025
  If the grinding table of your Renfert Laboratory Equipment is wobbling, ensure it is pushed all the way down onto the ball head. Check and increase the water volume at the trimmer, and ensure the water supply is fully open. Also, inspect the rinse tube and inlet strainer for any blockages, cleaning or decalcifying them as necessary. Finally, verify that the rinse tube seal is attached.
A
anna66Aug 25, 2025
What to do if my Renfert MT3 Laboratory Equipment appliance or parts are defective?
- B
  Brandon LewisAug 26, 2025
  Send appliance in for repair.
M
Michelle ReyesAug 23, 2025
Why is the trimmer disc wobbling on my Renfert MT3?
- J
  jacqueline79Aug 23, 2025
  If the trimmer disc wobbles on your Renfert Laboratory Equipment, reinstall the disc according to the directions, ensuring it is mounted exactly on the lock pin and that all deposits are removed from the back of the disc. Also, check if the fastening screw is not tightened and tighten it if necessary.

Summary

Appliance Description

1.1 MT3

Details the MT3 model's specific features and components.

1.2 MT3 pro

Details the MT3 pro model's specific features and components.

Commissioning

Operation

3.1 Grinding Angle Adjustment

How to adjust the grinding angle for different models.

3.1.1 MT3

Specific steps for adjusting the grinding angle on the MT3 model.

3.1.2 MT3 pro

Specific steps for adjusting the grinding angle on the MT3 pro model.

3.2 Adjust the water flowrate

Instructions on how to regulate the water flow rate at the inlet.

3.3 Trimming

Guidance on the trimming process, including model placement and disc contact.

3.4 Trimmer Disc Replacement

Step-by-step guide for replacing the trimmer disc.

Cleaning and Maintenance

4.6 Flange Replacement

Detailed instructions for removing and replacing the flange component.

Troubleshooting

Device fails to start

Common causes and solutions when the appliance does not start.

MT3 pro: On;off button

Troubleshooting for the MT3 pro's on/off button activation.

Trimmer disc wobbles

Issues related to the trimmer disc not sitting flush or wobbling.

Red LED is on

Interpreting the red LED indicator when it is illuminated.

Appliance turns off

Red LED flashing at 1 Hz

Red LED flashing at 4 Hz

Red LED flashing at 2 Hz

Information for the purchaser

A. Application

A.1 Correct use of the unit

A.2 Unapproved use

B. Hazards and warnings

Critical safety warnings and potential hazards associated with operating the appliance.

E. Repair

G. Technical data

Specifications and technical details of the MT3 and MT3 pro models.

Renfert MT3 Specifications

General

Brand	Renfert
Model	MT3
Category	Laboratory Equipment
Language	English