Why can't I select a server connected to a slave on my Rextron Switch?
If you cannot select a server connected to a slave, it may be due to an improper Master unit connection. Only Master ports PC1~PC8 can be connected to slaves.
What to do if nothing works on my Rextron Switch?
If nothing is working, it might be due to a bad connection at the C-36 connectors. Push the assembled drawer and the KVM module box firmly together, leaving only 8mm (5/16 inch) space in between, and secure them with two screws.
How to fix a fuzzy or unclear VGA image on my Rextron Switch?
If the VGA image is fuzzy or not very clear, the cause may be poor quality VGA cables. Use UL-2919 rated VGA cables for video connection, as these cables use coaxial wires for R/G/B signals.
What should I do if the hotkey command is not effective on my Rextron Switch?
If the hotkey command isn't working, it's likely due to an incorrect hotkey sequence. To select a server connected to the Master, use three keystrokes. To select a server connected to a Slave, use four keystrokes.
What to do if the VGA monitor works fine, but the keyboard and touch pad do not work on my Rextron Switch?
If the VGA monitor works but the keyboard and touch pad don't, the connection inside the KVM drawer may be loose due to vibration. Disconnect the KVM drawer from the KVM module box. Connect a keyboard, mouse, and monitor to the Local port on the KVM module box, and another server to any of the PC ports, then use the KVM module box as a stand-alone KVM switch to verify if the KVM drawer is bad.
Why don't the keyboard and mouse work with my Rextron INTEGRA KVM2?
If the keyboard and mouse aren't working, it could be due to incorrect mini-DIN 8 cables. Use only straight-through, 1-to-1, 2-to-2, 8-to-8 mini-DIN 8 cables.
Why does the Integra fail to function occasionally on my Rextron INTEGRA KVM2?
The Integra may occasionally fail to function if the servers do not supply enough power. Make sure a power adapter with a minimum of 12V, 3.0A output rating is firmly connected to the power jack.
Why does my Rextron INTEGRA KVM2 master/slave setup not work?
If the master/slave setup does not work, it may be due to improper installation procedures. Make sure the slave’s CONSOLE is connected to the Master’s PC 1~ PC 8 port. Remove any possible power supply to the slave (unplug all cables) before connecting it to the Master.
Why is there no VGA output after connecting a 13w3-to-HDB15 adapter to a server on my Rextron INTEGRA KVM2?
If there is no VGA output after connecting a 13w3-to-HDB15 adapter, it could be due to an incorrect 13W3-to-HDB15 pin assignment. Use only the adapter specifically designed for Sun servers.
Why do the keys not work in Manual Scan on my Rextron INTEGRA KVM2?
The keys may not work in Manual Scan if all PCs are off, or only one PC is turned on. Scan mode works for power-on servers only, so turn the servers on.
Details the one-console and two-console matrix Sun KVM switches and their high video quality.
Highlights features like managing multiple servers, cascade configuration, and hot-plugging.
Explains connecting a Sun KVM Switch with an Integra Console to multiple Sun servers using cables.
Describes connecting second level KVM switches to a Master unit for expanded server control.
Guides connecting a TFT LCD KVM drawer or monitor/keyboard/mouse to the KVM switch's console port.
Explains connecting Sun servers using mini-DIN8 and HDB15 VGA cables to the KVM module.
Steps for powering up a single Integra Sun KVM Switch system by connecting power and turning on servers.
Steps for powering up cascaded Integra Sun KVM Switches, connecting power to master and slaves.
Details hot-key sequences for server selection, auto-scan, and audio stick control.
Describes how the KVM console emulates a Sun keyboard and maps extra keys.
Instructions for mapping specific keys for Japanese keyboards using combo-key sequences.
Details connecting servers or slave KVM switches to the Master unit's PC ports.
Explains how to change device connections at PC ports while the system is running.
Lists technical specifications for Integra Sun KVM Switch models ISM108 and ISM2208.
Offers common problems, their causes, and solutions for system issues.
Solutions for common VGA output problems like fuzzy images or no video signal.
Solutions for keyboard errors, non-working input devices, or shifted keystrokes.
General| Device Type | KVM switch |
|---|---|
| Product Type | KVM switch |
| Model | INTEGRA KVM2 |
| Number of Computers Supported | 2 |
| Number of Local Users Supported | 1 |
| Audio Support | Yes |
| Number of Ports | 2 Port |
| Compatibility | Mac |
| Cable Length | 1.8m |
| Switching Method | Hotkey, Button |
To Next Page
