!
!
#+!
Hot-key commands
Hot-key command is a short key board sequence to select a computer,
to activate computer scan, etc. NovaView interprets keystrokes for
hot-keys all the time. A hot-key sequence starts with two left
<CTRL> keystrokes followed by one or two more keystrokes. A
built-in buzzer generates a high-pitch beep for correct hot-key
command; otherwise, one low-pitch beep for error and the bad key
sequence will not be f orwarded to the selected computer.
The short form hot-key menu can be turned on as an OSD f unction
(<F4>:more\Hotkey Menu) every time the left <CTRL> key is pressed
twice.
L-CTRL
: is the <CTRL> key located at the left side of the
key board.
1~8/A~H
: are the number keys '1' ~ '8' at the upper row of the
key board and character keys 'A' ~ 'H' case
insensitive. Do not use t he k ey pad at the right of
the keyboard.
& To select a computer by hot-key command, you must know its
channel address, which is determined by the NovaView
connection. For a computer connected to a Master, its address
is represented by the PC port label (1~8 or A~H). For a
computer connected to a Slave, two characters represent its
address. The first character is the channel address of the Master
unit (1~8) and the second one is the channel address of the Slave
(1~8 or A~H). Please note that only Master's 'PC 1' ~'PC 8' ports
can be connected to a Slave.
Left Ctrl + lef t Ctrl + 7
Selects a computer connected to port 7 of the Master.
Left Ctrl + lef t Ctrl + 6 + C
Selects a computer connected to port C of a Slave connected
to port 6 of the Master.
& To s t a rt Auto Scan, automatically scan power-on
computers one
by one at a f ixed interv al:
left Ctrl + lef t Ctrl + F 1
!
!
#"!
When Auto Scan detects any keyboard or mouse activity, it
suspends the scanning till activity stops; it then resumes with the
next computer in sequence. The length of the Auto Scan interv al
(Scan Rate) is adjustable, see below. To abort the Auto Scan
mode, press the lef t Ctrl key twice.
Note: For OSD models, Scan Type determines whether ey e mark is
necessary during Auto Scan.
& Manual Scan enables you to manually switch back and forth
between power-on
computers.
left Ctrl + lef t Ctrl + F2
Press
#
##
#
or
$
$$
$
to select the previous or the next computer in
sequence. And, press any other key to abort the Manual Scan.
Note: For OSD models, Scan Type determines whether ey e mark is
necessary during Manual Scan.
& To adjust Scan Rate which sets the duration before switching to
the next computer in Auto Scan:
left Ctrl + lef t Ctrl + F3
The NovaView sends one to four beeps indicating scan interval of 3,
8, 15 and 30 seconds respectively.
& To adjust keyboard typematic rate (characters/sec), this setting
over-rides that of BIOS and any operating system:
left Ctrl + lef t Ctrl + F4
The NovaView generates 1 to 4 beeps corresponding to 10, 15, 20
and 30 characters/sec respectively.
& Audio Stick
An optional multimedia module can be LINKed to the back of each
Nov aView f or selecting microphone and stereo speaker signals.
There are two options f or Audio Stick:
ON
and
Off
. When set to
'
On
', audio selection follows computer selection. When set to '
Off
',
audio selection stops f ollowing computer selection. It is useful if
you want to listen to a particular computer's audio signal while
operating other computers.
left Ctrl + lef t Ctrl + F5
The NovaView generates 1 or 2 beeps corresponding to On and Off
respectively.