Rigol DS2302A - Page 158

To Next Page

To Previous Page

RIGOL Chapter 6 MATH and Measurements

6-16 MSO2000A/DS2000A User Guide

Note: The waveform auto setting function requires that the frequency of the sine

should be no lower than 25 Hz. If the parameter exceeds the limit, the waveform

auto setting function might be invalid.

Main Page

default chapter3
- Guaranty and Declaration3
- Safety Requirement4
- Safety Terms and Symbols7
- Allgemeine Sicherheits Informationen8
- Sicherheits Begriffe und Symbole11
- Measurement Category12
- Ventilation Requirement13
- Working Environment14
- Care and Cleaning16
- Environmental Considerations17
- MSO2000A/DS2000A Series Overview18
- Document Overview20
- Table of Contents23
Chapter 1 Quick Start31
- General Inspection32
- Appearance and Dimensions33
- To Prepare the Oscilloscope for Use34
- To Adjust the Supporting Legs34
- To Connect to Power Supply34
- Turn-On Checkout35
- To Connect the Probe35
- Function Inspection37
- Probe Compensation38
- Front Panel Overview39
- Rear Panel Overview41
- Front Panel Function Overview43
- Vertical43
- Horizontal44
- Trigger45
- Clear46
- Run/Stop46
- Single46
- Auto46
- Multifunction Knob47
- Navigation Knob47
- Function Keys48
- Signal Source49
- Record49
- Print49
- Logic Analyzer50
- User Interface51
- To Use the Security Lock56
- To Use the Built-In Help System57
Chapter 2 To Set the Vertical System59
- To Enable the Analog Channel60
- Channel Coupling61
- Bandwidth Limit61
- Probe Ratio62
- Input Impedance63
- Waveform Invert63
- Vertical Scale64
- Vertical Expansion65
- Amplitude Unit65
- Channel Label65
- Delay Calibration of the Analog Channel67
Chapter 3 To Set the Horizontal System69
- Delayed Sweep70
- Time Base Mode72
- Y-T Mode72
- X-Y Mode72
- Roll Mode75
- Horizontal Scale76
- Horizontal Reference77
Chapter 4 To Set the Sample System79
- Acquisition Mode80
- Normal80
- Average80
- Peak Detect82
- High Resolution82
- Sample Mode83
- Sample Rate84
- LA Sample Rate85
- Memory Depth86
- LA Memory Depth87
- Anti-Aliasing87
Chapter 5 To Trigger the Oscilloscope89
- Trigger Source90
- Trigger Mode91
- Trigger Coupling93
- Trigger Holdoff94
- Noise Rejection95
- Trigger Type96
- Edge Trigger97
- Pulse Trigger99
- Runt Trigger102
- Windows Trigger (Option)105
- Nth Edge Trigger (Option)107
- Slope Trigger109
- Video Trigger (HDTV Option)112
- Pattern Trigger115
- Delay Trigger (Option)117
- Timeout Trigger (Option)120
- Duration Trigger (Option)122
- Setup/Hold Trigger124
- RS232 Trigger126
- I2C Trigger129
- SPI Trigger132
- USB Trigger (Option)135
- CAN Trigger (Option)137
- Trigger Output Connector141
Chapter 6 MATH and Measurements143
- Math Operation144
- Addition144
- Subtraction144
- Multiplication145
- Division145
- Fft147
- Digital Filter150
- Logic Operation152
- Advanced Operation154
- MATH Label156
- Auto Measurement157
- Quick Measurement after AUTO157
- One-Key Measurement of 29 Parameters159
- Frequency Counter Measurement165
- Measurement Setting166
- To Clear the Measurement168
- All Measurement169
- Statistic Function170
- Measurement History170
- Cursor Measurement171
- Manual Mode172
- Track Mode177
- Auto Mode180
- X-Y Mode181
Chapter 7 Digital Channel183
- To Select the Digital Channel184
- To Move the Digital Channel184
- To Turn On/Off the Digital Channel185
- Group Set186
- To Set the Waveform Display Size187
- Reorder Setting187
- To Set the Threshold187
- To Use the Digital Bus188
- To Set the Label189
- Digital Channel Delay Calibration190
Chapter 8 Protocol Decoding191
- Parallel Decoding192
- RS232 Decoding (Option)195
- I2C Decoding (Option)200
- SPI Decoding (Option)204
- CAN Decoding (Option)207
Chapter 9 Reference Waveform211
- To Enable REF Function212
- To Set the Color212
- To Select REF Source212
- To Save REF Waveform213
- To Adjust REF Waveform Display213
- To Export to Internal or External Memory213
- To Import from Internal or External Memory214
Chapter 10 Pass/Fail Test215
- To Enable Pass/Fail Test216
- To Select Source216
- Mask Range216
- To Set Test Results Output Type218
- To Save the Test Mask219
- To Load the Test Mask219
Chapter 11 Waveform Recording221
- Waveform Recording222
- Record Constant on224
- Waveform Playback226
- Waveform Analysis228
- Analysis Based on Trace232
- Analysis Based on Pass/Fail Mask233
Chapter 12 Display Control235
- To Select the Display Type236
- To Set the Persistence Time236
- To Set the Waveform Intensity238
- To Set the Screen Grid238
- To Set the Grid Brightness238
- To Set the Menu Display238
Chapter 13 Signal Source239
- Parameter Setting Method240
- To Output Basic Waveform241
- To Output Sine241
- To Output Square242
- To Output Ramp243
- To Output Pulse244
- To Output DC244
- To Output Noise245
- To Output Built-In Waveform246
- To Output Arbitrary Waveform250
- To Select Waveform252
- To Create Waveform252
- To Edit Waveform254
- Modulation257
Chapter 14 Store and Recall261
- Storage System262
- Storage Type263
- Internal Storage and Recall265
- External Storage and Recall267
- Disk Management269
- To Select File Type269
- To Create a New File or Folder270
- To Delete a File or Folder273
- To Rename a File or Folder274
- To Clear the Local Memory274
- Factory275
Chapter 15 System Function Setting283
- Remote Interface Configuration284
- LAN Setting284
- USB Device289
- GPIB Address289
- System-Related290
- Sound290
- Language290
- System Information291
- Power-Off Recall291
- System Time292
- Screen293
- Self-Calibration294
- Print Setting295
- Power Status297
- Aux Output298
- Option Management299
- Auto Setting301
Chapter 16 Remote Control303
- Remote Control Via USB304
- Remote Control Via LAN308
- Remote Control Via GPIB310
Chapter 17 Troubleshooting313
Appendix A: Accessories and Options317
Chapter 18 Appendix317
Appendix B: Warranty319
- Index321

Rigol DS2302A - Page 158

Table of Contents

Other manuals for Rigol DS2302A

Related product manuals