12
Press and hold to turn on the robot. The
power indicator light will come on, and the
robot will be on standby.
Press and hold
to turn off the robot and
complete the cleaning cycle.
Turning On/Off
The robot cannot be turned off when it is being
charged.
Note:
Press to start cleaning. The robot will
plan its cleaning route and in each room,
it firstly draws out edges and then fills
the room in a zigzag pattern. In so doing,
the robot cleans all rooms one by one,
thoroughly and efficiently.
Starting Cleaning
Notes:
• Before cleaning, tidy cords (including the power cord
of the dock) and valuables from the floor. Loose
items may be dragged by the robot, resulting in the
disconnection of electrical appliances or damage of
cords and property.
• Before starting each cleaning task, make sure that the
mop cloths have been properly installed.
• To make sure the robot returns to the dock
automatically, start the robot from the dock and do
not move the dock during cleaning.
• Cleaning cannot start if the battery level is too low.
Allow the robot to charge before starting a cleanup.
• If the battery runs low during a cleaning cycle, the
robot will automatically return to the dock. After
charging, the robot will resume where it left off.
• If cleaning is completed in less than 10 minutes, the
robot will clean the area twice.
• The robot will retract mop cloth mounts to clean the
carpet. You can also set the carpet as a no-go zone in
the app to avoid it.
Spot Cleaning
Press and simultaneously to start spot
cleaning. Cleaning range: The robot cleans
a 1.5 m (4.9 ft) × 1.5 m (4.9 ft) square area
centered on itself.
After spot cleaning, the robot will automatically
return to the starting point and be on standby.
Note:
Pause
When the robot is cleaning, tap any
button to pause it. When it is cleaning
under furniture or appliances, tap
and
then double tap
to pause it. To resume
cleaning, press
. Press on a paused
robot to send it back to the dock, and press
and hold
to wash the mop cloths and then
resume cleaning.
Mop Only
Press to start Mop Only. The main
brushes and side brush rise, the main
brushes and fan stop operating, and the
VibraRise module lowers.
Compared with other cleaning modes, noise
emanating from Mop Only is much lower.
Note:
Placing a paused robot on the dock manually will
end the current cleanup.
Note:
Sleep
If the robot is paused for over 10 minutes,
it will go to sleep, and the power indicator
light will flash every few seconds. Press any
button to wake the robot up.
Notes:
• The robot will not go to sleep when it is charging.
• The robot will automatically shut down if left sleep for
more than 12 hours.
Mop Washing
During cleaning, the robot automatically
determines when it should return to the dock
for mop washing and water tank refilling
to maximize its mopping performance. To
manually start washing, press and hold
or tap the corresponding button in the app.
Press any button to stop washing.
• To ensure the robot automatically washes the mop
cloths, start it from the dock and avoid moving the
dock during cleaning.
• Mop wash frequency and mode can be modified in
the app.
• To avoid burns from hot water, do not touch the clean
water dispensers.
Notes:
After cleaning, the robot will return to
the dock and auto-emptying will begin
as needed. To manually start emptying,
press
on the docked robot or tap the
corresponding button in the app. Press any
button to stop emptying.
Emptying
• When emptying has been left unused for a long
period, empty the dustbin manually and make sure
the air inlet is clear for optimal emptying performance.
• Auto-emptying can be disabled in the app.
• Avoid frequent manual emptying.
• Do not use without dust container door closed or
disposable dust bag installed in place.
Notes:
• If no floor cleaning solution is used daily, you may skip
this step or disable Smart Cleaning Solution Filling
in the app.
To Next Page
Loading...
