Roland CAMM-1 PNC-950 - Interface Specifications; Parallel Interface Specifications; Serial Interface Specifications

23
• Instructions in mode1 and mode2
Instruction Format Meanin
g
of Parameter [Parameter Ran
g
e (Default)] Explanation
IW IW LLx, LL
y
, URx, UR
y
; LLx, LL
y
: lower left coordinates of window In
p
ut Window
IW; URx,UR
y
: U
pp
er ri
g
ht coordinates of window
LB LB c1c2c3...cn c: Character strin
g
Label
[label terminator]
LT LT n(,l); n: Pattern number [0 — 6 (solid line)] Line T
yp
e
LT; l: 1
p
itch len
g
th [*2 (1.5% of (P2-P1))]
OA OA; None Out
p
ut Actual Point
OC OC; None Out
p
ut Commanded Position
OE OE; None Out
p
ut Error
OF OF; None Out
p
ut Factor
When the PNC-950 receives an OF instruction from the com
p
uter,
"40,40 [TERM]" is out
p
ut.
OH OH; None Out
p
ut Hard-Cli
p
Limits
OI OI; None Out
p
ut Identification
When the PNC-950 receives an OI instruction from the com
p
uter,
"950 [TERM]" is out
p
ut.
OO OO; None Out
p
ut O
p
tion Parameter
When the PNC-950 receives an OO instruction from the com
p
uter,
"0,0,0,0,1,0,0,0 [TERM]" is out
p
ut. The "1" in this out
p
ut indicates that
circle and arc commands have been loaded
OP OP; None Out
p
ut P1 & P2
OS OS; None Out
p
ut Status
OW OW; None Out
p
ut Window
PA PA x1,
y
1(...,xn,
y
n); xn,
y
n: Absolute XY coordinates [*1] Cut Absolute
PA;
PD PD x1,
y
1(...,xn,
y
n); xn,
y
n: XY coordinates [*1] Tool Down
PD;
PR PR 1,
y
1(... xn,
y
n); xn,
y
n: Relative XY coordinates [*1] Cut Relative
PR;
PT PT d; d: Pen thickness (mm) [0—5 (0.3)] Pen Thickness
PT;
PU PU x1,
y
1(...,xn,
y
n); xn,
y
n: XY coordinates [*1] Tool U
p
PU;
RA RA x,
y
; x,
y
: Absolute XY coordinates of o
pp
osite an
g
le of rectan
g
le [*1] Shade Rectan
g
le Absolute
RR RR x,
y
; x,
y
: Relative XY coordinates of o
pp
osite an
g
le of rectan
g
le [*1] Shade Rectan
g
le Relative
SA SA; None Select Alternate Set
SC SC Xmin, Xmax, Ymin, Ymax; Xmin, Ymin: User XY coordinates of P1 [*1] Scalin
g
SC; Xmax, Ymax: User XY coordinates of P2 [*1]
SI SI w, h; w: Character width (cm.) [-128 — +127.99999 (3.8)] Absolute Character Size
SI; h: Character hei
g
ht (cm.) [-128 — +127.99999 (5)]
SL SL tanØ; tanØ: Character slant [*1 (0)] Character Slant
SL;
SM SM s; s: Character or s
y
mbol [*4 (Default: S
y
mbol Mode
SM; Clears s
y
mbol mode)]
SR SR w, h; w: Character width (%) [*1 (3.8 )] Relative Character Size
SR; h: Character hei
g
ht (%) [*1 (5 )]
SS SS; None Select Standard Set
TL TL l
p
(,lm); l
p
: Tick len
g
th in
p
ositive direction [*2 (0.5%)] Thick Len
g
th
TL; lm: Tick len
g
th in ne
g
ative direction [*2 (0.5%)]
UC UC (c,) x,
y
,(c,) c: Tool control value [-(67108863) — -99, +99 — +(67108863)] User Defined Character
,...., xn,
y
n; xn: Units of movement in X-axis direction [-99< xn<+99]
UC;
y
n: Units of movement in Y-axis direction [-99<
y
n<+99]
VS VS v; v: Tool s
p
eed (cm/sec.) [1 — 40 ] Velocit
y
Select
VS;
WG WG r, Ø1, Øc(,Ød); r : Radius [*1] Shade Wed
g
e
Ø1 : Start an
g
le [*3]
Øc : Center an
g
le [*3]
Ød : Chord tolerance [*3 (5°)]
XT XT; None X-Tick
YT YT; None Y-Tick
Instruction Format Meanin
g
of Parameter [Parameter Ran
g
e (Default)] Explanation
!NR !NR [terminator] None Not Read
y
!PG !PG n [terminator] n: [-24998 — +24998 mm] Pa
g
e Feed
!ST !ST n [terminator] n: [0, 1] Select Tool