Roland juno-ds61 - MFX;Chorus;Reverb Parameters; Distortion Delay and Enhancer Chorus; Enhancer Delay and Chorus Delay

56
MFX/Chorus/Reverb Parameters
68: OD
0
DELAY
L in
R in
Delay
Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
Parameter Value Explanation
Overdrive Drive # 0–127
Degree of distortion
Also changes the volume.
Overdrive Pan # L64–63R Stereo location of the overdrive sound
Delay Time 0–2600[msec], note
Adjusts the delay time from the direct sound until
the delay sound is heard.
Delay Feedback # -98–+98[%]
Adjusts the proportion of the delay sound that is
fed back into the eect.
Negative (-) settings will invert the phase.
Delay HF Damp 200–8000[Hz], note
Adjusts the frequency above which sound fed
back to the eect will be cut. If you do not want
to cut the high frequencies, set this parameter to
BYPASS.
Delay Balance # D100:0W–D0:100W
Adjusts the volume balance between the sound
that is sent through the delay (W) and the sound
that is not sent through the delay (D).
Level 0–127 Output level
69: DST
0
CHORUS
The parameters are essentially the same as in “66: OD
0
CHORUS” with the
exception of the following two.
Overdrive Drive
0
Distortion Drive,
Overdrive Pan
0
Distortion Pan
L in
R in
Chorus
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
70: DST
0
FLANGER
The parameters are essentially the same as in “67: OD
0
FLANGER,” with the
exception of the following two.
Overdrive Drive
0
Distortion Drive,
Overdrive Pan
0
Distortion Pan
L in
R in
Flanger
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
71: DST
0
DELAY
The parameters are essentially the same as in “68: OD
0
DELAY,” with the exception
of the following two.
Overdrive Drive
0
Distortion Drive,
Overdrive Pan
0
Distortion Pan
L in
R in
Delay
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
72: ENH
0
CHORUS
Chorus
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
Enhancer Sens # 0–127 Sensitivity of the enhancer
Enhancer Mix # 0–127
Level of the overtones generated by the
enhancer
Chorus Pre Delay 0.0–100[msec]
Adjusts the delay time from the direct sound
until the chorus sound is heard.
Chorus Rate # 0.05–10.00[Hz], note Frequency of modulation
Chorus Depth 0–127 Depth of modulation
Chorus Balance # D100:0W–D0:100W
Adjusts the volume balance between the sound
that is sent through the chorus (W) and the
sound that is not sent through the chorus (D).
Level 0–127 Output level
73: ENH
0
FLANGER
Feedback
Flanger
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
Enhancer Sens # 0–127 Sensitivity of the enhancer
Enhancer Mix # 0–127
Level of the overtones generated by the
enhancer
Flanger Pre Delay 0.0–100[msec]
Adjusts the delay time from when the direct
sound begins until the anger sound is heard.
Flanger Rate # 0.05–10.00[Hz], note Frequency of modulation
Flanger Depth 0–127 Depth of modulation
Flanger Feedback # -98–+98[%]
Adjusts the proportion of the anger sound that
is fed back into the eect.
Negative (-) settings will invert the phase.
Flanger Balance # D100:0W–D0:100W
Adjusts the volume balance between the sound
that is sent through the anger (W) and the
sound that is not sent through the anger (D).
Level 0–127 Output level
74: ENH
0
DELAY
Feedback
Delay
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
Enhancer Sens # 0–127 Sensitivity of the enhancer
Enhancer Mix # 0–127 Level of the overtones generated by the enhancer
Delay Time 0–2600[msec], note
Adjusts the delay time from the direct sound until
the delay sound is heard.
Delay Feedback # -98–+98[%]
Adjusts the proportion of the delay sound that is
fed back into the eect.
Negative (-) settings will invert the phase.
Delay HF Damp
200–8000[Hz],
BYPASS
Adjusts the frequency above which sound fed
back to the eect will be cut. If you do not want
to cut the high frequencies, set this parameter to
BYPASS.
Delay Balance # D100:0W–D0:100W
Adjusts the volume balance between the sound
that is sent through the delay (W) and the sound
that is not sent through the delay (D).
Level 0–127 Output level
75: CHORUS
0
DELAY
Feedback
Delay
L in
R in
L out
R out
Balance W
Balance W
Balance D
Balance D
Chorus
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
Chorus Pre Delay 0.0–100[msec]
Adjusts the delay time from the direct sound
until the chorus sound is heard.
Chorus Rate # 0.05–10.00[Hz], note Frequency of modulation
Chorus Depth 0–127 Depth of modulation
Chorus Balance # D100:0W–D0:100W
Volume balance between the direct sound (D)
and the chorus sound (W)
Delay Time 0–2600[msec], note
Adjusts the delay time from the direct sound
until the delay sound is heard.
3
3
3
3
3