Roland juno-ds61 - MFX;Chorus;Reverb Parameters; Chorus Parameter Details; Reverb Parameter Details

58
MFX/Chorus/Reverb Parameters
Chorus Parameters
Parameter Explanation
01: CHORUS
Filter Type
Type of lter
OFF No lter is used
LPF Cuts the frequency range above the Cuto Freq
HPF Cuts the frequency range below the Cuto Freq
Cuto Freq
Basic frequency of the lter
200–8000[Hz]
Pre Delay
Adjusts the delay time from the direct sound until the chorus sound is
heard.
0.0–100.0[msec]
Rate
Frequency of modulation
0.05–10.00Hz, note
Depth
Depth of modulation
0–127
Phase
Spatial spread of the sound
0–180[deg]
Feedback
Adjusts the amount of the chorus sound that is fed back into the eect.
0–127
02: DELAY
Delay Left, Right,
Center
Adjusts the delay time from the direct sound until the delay sound is
heard.
0–1000ms, note
Center Feedback
Adjusts the proportion of the delay sound that is fed back into the eect.
Negative (-) settings will invert the phase.
-98–+98[%]
HF Damp
Adjusts the frequency above which sound fed back to the eect will be
cut. If you do not want to cut the high frequencies, set this parameter to
BYPASS.
200–8000[Hz], BYPASS
Left, Right, Center
Level
Volume of each delay sound
0–127
03: GM2 CHORUS
Pre-LPF
Cuts the high frequency range of the sound coming into the chorus.
0–7
Level
Volume of the chorus sound
0–127
Feedback
Adjusts the amount of the chorus sound that is fed back into the eect.
0–127
Rate
Frequency of modulation
0–127
Depth
Depth of modulation
0–127
Send Level To Rev
Adjusts the amount of chorus sound that will be sent to the reverb.
0–127
Reverb Parameters
Parameter Explanation
01: REVERB
Type
Type of reverb/delay
ROOM1 Short reverb with high density
ROOM2 Short reverb with low density
STAGE1 Reverb with greater late reverberation
STAGE2 Reverb with strong early reections
HALL1 Very clear-sounding reverb
HALL2 Rich reverb
DELAY Conventional delay eect
PAN-DELAY Delay eect with echoes that pan left and right
Time
Time length of reverberation (Type: ROOM1–HALL2)
Delay time (Type: DELAY, PAN-DELAY)
0–127
HF Damp
Adjusts the frequency above which the high-frequency content of the
reverb sound will be cut, or “damped.” If you do not want to cut the high
frequencies, set this parameter to BYPASS.
200–8000[Hz], BYPASS
Delay Feedback
Adjusts the amount of delay feedback when the Type setting is DELAY or
PAN-DELAY. Amount of delay sound returned to the input (this setting is
valid only if Type is DELAY or PAN-DELAY)
0–127
02: SRV ROOM / 03: SRV HALL / 04: SRV PLATE
Pre Delay
Adjusts the delay time from the direct sound until the reverb sound is
heard.
0.0–100.0[msec]
Time
Time length of reverberation
0–127
Size
Size of the simulated room or hall
1–8
High Cut
Adjusts the frequency above which the high-frequency content of the
reverb will be reduced. If you do not want to reduce the high frequencies,
set this parameter to BYPASS.
160–12500[Hz], BYPASS
Density
Density of reverb
0–127
Diusion
Adjusts the change in the density of the reverb over time. The higher the
value, the more the density increases with time. (The eect of this setting
is most pronounced with long reverb times.)
0–127
LF Damp Freq
Adjusts the frequency below which the low-frequency content of the
reverb sound will be reduced, or “damped.”
50–4000[Hz]
LF Damp Gain
Adjusts the amount of damping applied to the frequency range selected
with LF Damp. With a setting of “0,” there will be no reduction of the
reverb’s low-frequency content.
-36–0[dB]
HF Damp Freq
Adjusts the frequency above which the high-frequency content of the
reverb sound will be reduced, or “damped.”
4000–12500[Hz]
HF Damp Gain
Adjusts the amount of damping applied to the frequency range selected
with HF Damp. With a setting of “0,” there will be no reduction of the
reverb’s high-frequency content.
-36–0[dB]
05: GM2 REVERB
Character
Type of reverb
0–5 Reverb
6, 7 Delay
Pre-LPF
Cuts the high frequency range of the sound coming into the reverb.
0–7
Level
Output level of reverberation
0–127
Time
Time length of reverberation
0–127
Delay Feedback
Adjusts the amount of the delay sound that is fed back into the eect
when the Reverb Character setting is 6 or 7.
0–127